Vulnerabilities (CVE)

An Improper Check for Unusual or Exceptional Conditions vulnerability in the packet forwarding engine (PFE) of Juniper Networks Junos OS on EX4k Series and QFX5k Series platforms allows an unauthenticated network-adjacent attacker flapping an interface to cause traffic between VXLAN Network Identifiers (VNIs) to drop, leading to a Denial of Service (DoS). On all EX4k and QFX5k platforms, a link flap in an EVPN-VXLAN configuration Link Aggregation Group (LAG) results in Inter-VNI traffic droppi ... An Improper Check for Unusual or Exceptional Conditions vulnerability in the packet forwarding engine (PFE) of Juniper Networks Junos OS on EX4k Series and QFX5k Series platforms allows an unauthenticated network-adjacent attacker flapping an interface to cause traffic between VXLAN Network Identifiers (VNIs) to drop, leading to a Denial of Service (DoS). On all EX4k and QFX5k platforms, a link flap in an EVPN-VXLAN configuration Link Aggregation Group (LAG) results in Inter-VNI traffic dropping when there are multiple load-balanced next-hop routes for the same destination. This issue is only applicable to systems that support EVPN-VXLAN Virtual Port-Link Aggregation Groups (VPLAG), such as the QFX5110, QFX5120, QFX5200, EX4100, EX4300, EX4400, and EX4650. Service can only be restored by restarting the affected FPC via the 'request chassis fpc restart slot <slot-number>' command. This issue affects Junos OS on EX4k and QFX5k Series:  * all versions before 21.4R3-S12,  * all versions of 22.2 * from 22.4 before 22.4R3-S8,  * from 23.2 before 23.2R2-S5,  * from 23.4 before 23.4R2-S5,  * from 24.2 before 24.2R2-S3, * from 24.4 before 24.4R2.

Show More

A Heap-based Buffer Overflow vulnerability in the flexible PIC concentrator (FPC) of Juniper Networks Junos OS on EX2300, EX3400, EX4100, EX4300, EX4300MP, EX4400, EX4600, EX4650-48Y, and QFX5k Series allows an attacker to send a specific DHCP packet to the device, leading to an FPC crash and restart, resulting in a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. Under a rare timing scenario outside the attacker ... A Heap-based Buffer Overflow vulnerability in the flexible PIC concentrator (FPC) of Juniper Networks Junos OS on EX2300, EX3400, EX4100, EX4300, EX4300MP, EX4400, EX4600, EX4650-48Y, and QFX5k Series allows an attacker to send a specific DHCP packet to the device, leading to an FPC crash and restart, resulting in a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. Under a rare timing scenario outside the attacker's control, memory corruption may be observed when DHCP Option 82 is enabled, leading to an FPC crash and affecting packet forwarding. Due to the nature of the heap-based overflow, exploitation of this vulnerability could also lead to remote code execution within the FPC, resulting in complete control of the vulnerable component. This issue affects Junos OS on EX2300, EX3400, EX4100, EX4300, EX4300MP, EX4400, EX4600, EX4650-48Y, and QFX5k Series: * All versions before 21.4R3-S9,  * from 22.2 before 22.2R3-S5,  * from 22.4 before 22.4R3-S5,  * from 23.2 before 23.2R2-S3,  * from 23.4 before 23.4R2-S3,  * from 24.2 before 24.2R2.

Show More

An Unimplemented or Unsupported Feature in UI vulnerability in the CLI of Juniper Networks Junos OS Evolved on QFX5000 Series allows an unauthenticated, adjacent attacker to cause a Denial-of-Service (DoS). Several configuration statements meant to enforce limits on MAC learning and moves can be configured but do not take effect. This can lead to control plane overload situations which will severely impact the ability of the device to processes legitimate traffic. This issue affects Junos OS ... An Unimplemented or Unsupported Feature in UI vulnerability in the CLI of Juniper Networks Junos OS Evolved on QFX5000 Series allows an unauthenticated, adjacent attacker to cause a Denial-of-Service (DoS). Several configuration statements meant to enforce limits on MAC learning and moves can be configured but do not take effect. This can lead to control plane overload situations which will severely impact the ability of the device to processes legitimate traffic. This issue affects Junos OS Evolved on QFX5000 Series: * All versions before 21.4R3-S8-EVO, * 22.2-EVO versions before 22.2R3-S5-EVO, * 22.4-EVO versions before 22.4R3-EVO, * 23.2-EVO versions before 23.2R2-EVO.

Show More

An Uncontrolled Resource Consumption vulnerability in the http daemon (httpd) of Juniper Networks Junos OS on SRX Series, QFX Series, MX Series and EX Series allows an unauthenticated, network-based attacker to cause Denial-of-Service (DoS). An attacker can send specific HTTPS connection requests to the device, triggering the creation of processes that are not properly terminated. Over time, this leads to resource exhaustion, ultimately causing the device to crash and restart. The following co ... An Uncontrolled Resource Consumption vulnerability in the http daemon (httpd) of Juniper Networks Junos OS on SRX Series, QFX Series, MX Series and EX Series allows an unauthenticated, network-based attacker to cause Denial-of-Service (DoS). An attacker can send specific HTTPS connection requests to the device, triggering the creation of processes that are not properly terminated. Over time, this leads to resource exhaustion, ultimately causing the device to crash and restart. The following command can be used to monitor the resource usage: user@host> show system processes extensive | match mgd | count This issue affects Junos OS on SRX Series and EX Series: All versions before 21.4R3-S7, from 22.2 before 22.2R3-S4, from 22.3 before 22.3R3-S3, from 22.4 before 22.4R3-S2, from 23.2 before 23.2R2-S1, from 23.4 before 23.4R1-S2, 23.4R2.

Show More

An Origin Validation Error vulnerability in an insufficient protected file of Juniper Networks Junos OS on EX4600 Series and QFX5000 Series allows an unauthenticated attacker with physical access to the device to create a backdoor which allows complete control of the system. When a device isn't configured with a root password, an attacker can modify a specific file. It's contents will be added to the Junos configuration of the device without being visible. This allows for the addition of any co ... An Origin Validation Error vulnerability in an insufficient protected file of Juniper Networks Junos OS on EX4600 Series and QFX5000 Series allows an unauthenticated attacker with physical access to the device to create a backdoor which allows complete control of the system. When a device isn't configured with a root password, an attacker can modify a specific file. It's contents will be added to the Junos configuration of the device without being visible. This allows for the addition of any configuration unknown to the actual operator, which includes users, IP addresses and other configuration which could allow unauthorized access to the device. This exploit is persistent across reboots and even zeroization. The indicator of compromise is a modified /etc/config/<platform>-defaults[-flex].conf file. Review that file for unexpected configuration statements, or compare it to an unmodified version which can be extracted from the original Juniper software image file. For details on the extraction procedure please contact Juniper Technical Assistance Center (JTAC). To restore the device to a trusted initial configuration the system needs to be reinstalled from physical media.  This issue affects Junos OS on EX4600 Series and QFX5000 Series: * All versions before 21.4R3, * 22.2 versions before 22.2R3-S3.

Show More

An Improper Isolation or Compartmentalization vulnerability in the Packet Forwarding Engine (pfe) of Juniper Networks Junos OS on QFX5000 Series and EX Series allows an unauthenticated, adjacent attacker to cause a Denial of Service (DoS). If a specific malformed LACP packet is received by a QFX5000 Series, or an EX4400, EX4100 or EX4650 Series device, an LACP flap will occur resulting in traffic loss. This issue affects Junos OS on QFX5000 Series, and on EX4400, EX4100 or EX4650 Series: * ... An Improper Isolation or Compartmentalization vulnerability in the Packet Forwarding Engine (pfe) of Juniper Networks Junos OS on QFX5000 Series and EX Series allows an unauthenticated, adjacent attacker to cause a Denial of Service (DoS). If a specific malformed LACP packet is received by a QFX5000 Series, or an EX4400, EX4100 or EX4650 Series device, an LACP flap will occur resulting in traffic loss. This issue affects Junos OS on QFX5000 Series, and on EX4400, EX4100 or EX4650 Series: * 20.4 versions from 20.4R3-S4 before 20.4R3-S8, * 21.2 versions from 21.2R3-S2 before 21.2R3-S6, * 21.4 versions from 21.4R2 before 21.4R3-S4, * 22.1 versions from 22.1R2 before 22.1R3-S3, * 22.2 versions before 22.2R3-S1, * 22.3 versions before 22.3R2-S2, 22.3R3, * 22.4 versions before 22.4R2-S1, 22.4R3.

Show More

An Unimplemented or Unsupported Feature in the UI vulnerability in Juniper Networks Junos OS on QFX5000 Series and EX4600 Series allows an unauthenticated, network-based attacker to cause a minor integrity impact to downstream networks.If one or more of the following match conditions ip-source-address ip-destination-address arp-type which are not supported for this type of filter, are used in an ethernet switching filter, and then this filter is applied as an output filter, the configuration c ... An Unimplemented or Unsupported Feature in the UI vulnerability in Juniper Networks Junos OS on QFX5000 Series and EX4600 Series allows an unauthenticated, network-based attacker to cause a minor integrity impact to downstream networks.If one or more of the following match conditions ip-source-address ip-destination-address arp-type which are not supported for this type of filter, are used in an ethernet switching filter, and then this filter is applied as an output filter, the configuration can be committed but the filter will not be in effect. This issue affects Junos OS on QFX5000 Series and EX4600 Series: * All version before 21.2R3-S7,  * 21.4 versions before 21.4R3-S6, * 22.1 versions before 22.1R3-S5, * 22.2 versions before 22.2R3-S3, * 22.3 versions before 22.3R3-S2,  * 22.4 versions before 22.4R3, * 23.2 versions before 23.2R2. Please note that the implemented fix ensures these unsupported match conditions cannot be committed anymore.

Show More

An Improper Validation of Syntactic Correctness of Input vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). If an attacker sends high rate of specific ICMP traffic to a device with VXLAN configured, this causes a deadlock of the PFE and results in the device becoming unresponsive. A manual restart will be required to recover the device. This issue only affects EX4100, EX4400, EX4 ... An Improper Validation of Syntactic Correctness of Input vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). If an attacker sends high rate of specific ICMP traffic to a device with VXLAN configured, this causes a deadlock of the PFE and results in the device becoming unresponsive. A manual restart will be required to recover the device. This issue only affects EX4100, EX4400, EX4600, QFX5000 Series devices. This issue affects: Juniper Networks Junos OS * 21.4R3 versions earlier than 21.4R3-S4; * 22.1R3 versions earlier than 22.1R3-S3; * 22.2R2 versions earlier than 22.2R3-S1; * 22.3 versions earlier than 22.3R2-S2, 22.3R3; * 22.4 versions earlier than 22.4R2; * 23.1 versions earlier than 23.1R2.

Show More

In VxLAN scenarios on EX4300-MP, EX4600, QFX5000 Series devices an Uncontrolled Memory Allocation vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows an unauthenticated adjacently located attacker sending specific packets to cause a Denial of Service (DoS) condition by crashing one or more PFE's when they are received and processed by the device. Upon automatic restart of the PFE, continued processing of these packets will cause the memory leak to reappear. De ... In VxLAN scenarios on EX4300-MP, EX4600, QFX5000 Series devices an Uncontrolled Memory Allocation vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows an unauthenticated adjacently located attacker sending specific packets to cause a Denial of Service (DoS) condition by crashing one or more PFE's when they are received and processed by the device. Upon automatic restart of the PFE, continued processing of these packets will cause the memory leak to reappear. Depending on the volume of packets received the attacker may be able to create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on EX4300-MP, EX4600, QFX5000 Series: 17.1 version 17.1R1 and later versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R2-S13, 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R1-S8, 18.4R2-S6, 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S7, 19.2R3-S1; 19.3 versions prior to 19.3R2-S6, 19.3R3-S1; 19.4 versions prior to 19.4R1-S4, 19.4R2-S4, 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2-S3, 20.2R3; 20.3 versions prior to 20.3R2. This issue does not affect Junos OS versions prior to 17.1R1.

Show More

A NULL Pointer Dereference vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on QFX5000 Series and MX Series allows an unauthenticated adjacent attacker to cause a Denial of Service (DoS). On QFX5K Series and MX Series, when the PFE receives a specific VxLAN packet the Layer 2 Address Learning Manager (L2ALM) process will crash leading to an FPC reboot. Continued receipt of this specific packet will create a sustained Denial of Service (DoS) condition. This issue a ... A NULL Pointer Dereference vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on QFX5000 Series and MX Series allows an unauthenticated adjacent attacker to cause a Denial of Service (DoS). On QFX5K Series and MX Series, when the PFE receives a specific VxLAN packet the Layer 2 Address Learning Manager (L2ALM) process will crash leading to an FPC reboot. Continued receipt of this specific packet will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS on QFX5000 Series, MX Series: 20.3 versions prior to 20.3R3-S3; 20.4 versions prior to 20.4R3-S2; 21.2 versions prior to 21.2R2-S1. This issue does not affect Juniper Networks Junos OS: All versions prior to 20.3R1; 21.1 version 21.1R1 and later versions.

Show More

An Incorrect Comparison vulnerability in PFE of Juniper Networks Junos OS allows an adjacent unauthenticated attacker to cause a Denial of Service (DoS). On QFX5000 Series, and EX4600 and EX4650 platforms, the fxpc process will crash followed by the FPC reboot upon receipt of a specific hostbound packet. Continued receipt of these specific packets will create a sustained Denial of Service (DoS) condition. This issue only affects Juniper Networks Junos OS 19.4 version 19.4R3-S4.

A vulnerability in the processing of inbound IPv6 packets in Juniper Networks Junos OS on QFX5000 Series and EX4600 switches may cause the memory to not be freed, leading to a packet DMA memory leak, and eventual Denial of Service (DoS) condition. Once the condition occurs, further packet processing will be impacted, creating a sustained Denial of Service (DoS) condition. The following error logs may be observed using the "show heap" command and the device may eventually run out of memory if suc ... A vulnerability in the processing of inbound IPv6 packets in Juniper Networks Junos OS on QFX5000 Series and EX4600 switches may cause the memory to not be freed, leading to a packet DMA memory leak, and eventual Denial of Service (DoS) condition. Once the condition occurs, further packet processing will be impacted, creating a sustained Denial of Service (DoS) condition. The following error logs may be observed using the "show heap" command and the device may eventually run out of memory if such packets are received continuously. Jan 12 12:00:00 device-name fpc0 (buf alloc) failed allocating packet buffer Jan 12 12:00:01 device-name fpc0 (buf alloc) failed allocating packet buffer user@device-name> request pfe execute target fpc0 timeout 30 command "show heap" ID Base Total(b) Free(b) Used(b) % Name -- ---------- ----------- ----------- ----------- --- ----------- 0 246fc1a8 536870488 353653752 183216736 34 Kernel 1 91800000 16777216 12069680 4707536 28 DMA 2 92800000 75497472 69997640 5499832 7 PKT DMA DESC 3 106fc000 335544320 221425960 114118360 34 Bcm_sdk 4 97000000 176160768 200 176160568 99 Packet DMA <<<<<<<<<<<<<< 5 903fffe0 20971504 20971504 0 0 Blob This issue affects Juniper Networks Junos OS on QFX5000 Series, EX4600: 18.3R3 versions prior to 18.3R3-S6; 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.1 versions prior to 19.1R2-S3, 19.1R3-S7; 19.2 versions prior to 19.2R1-S8, 19.2R3-S3; 19.3 versions prior to 19.3R2-S7, 19.3R3-S4; 19.4 versions prior to 19.4R2-S5, 19.4R3-S6; 20.1 versions prior to 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2-S1, 21.1R3; 21.2 versions prior to 21.2R1-S1, 21.2R2. This issue does not affect Juniper Networks Junos OS: Any versions prior to 17.4R3; 18.1 versions prior to 18.1R3-S6; 18.2 versions prior to 18.2R3; 18.3 versions prior to 18.3R3; 18.4 versions prior to 18.4R2; 19.1 versions prior to 19.1R2.

Show More