Vulnerabilities (CVE)

A vulnerability in the IP packet processing of Cisco Access Point (AP) Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to insufficient input validation of certain IPv4 packets. An attacker could exploit this vulnerability by sending a crafted IPv4 packet either to or through an affected device. A successful exploit could allow the attacker to cause an affected device to reload unexpectedly, ... A vulnerability in the IP packet processing of Cisco Access Point (AP) Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to insufficient input validation of certain IPv4 packets. An attacker could exploit this vulnerability by sending a crafted IPv4 packet either to or through an affected device. A successful exploit could allow the attacker to cause an affected device to reload unexpectedly, resulting in a DoS condition. To successfully exploit this vulnerability, the attacker does not need to be associated with the affected AP. This vulnerability cannot be exploited by sending IPv6 packets.

Show More

A vulnerability in the Network Configuration Access Control Module (NACM) of Cisco IOS XE Software could allow an authenticated, remote attacker to obtain unauthorized read access to configuration or operational data. This vulnerability exists because a subtle change in inner API call behavior causes results to be filtered incorrectly. An attacker could exploit this vulnerability by using either NETCONF, RESTCONF, or gRPC Network Management Interface (gNMI) protocols and query data on paths t ... A vulnerability in the Network Configuration Access Control Module (NACM) of Cisco IOS XE Software could allow an authenticated, remote attacker to obtain unauthorized read access to configuration or operational data. This vulnerability exists because a subtle change in inner API call behavior causes results to be filtered incorrectly. An attacker could exploit this vulnerability by using either NETCONF, RESTCONF, or gRPC Network Management Interface (gNMI) protocols and query data on paths that may have been denied by the NACM configuration. A successful exploit could allow the attacker to access data that should have been restricted according to the NACM configuration. Note: This vulnerability requires that the attacker obtain the credentials from a valid user with privileges lower than 15, and that NACM was configured to provide restricted read access for that user.

Show More

A vulnerability in the Cisco Express Forwarding functionality of Cisco IOS XE Software for Cisco ASR 903 Aggregation Services Routers with Route Switch Processor 3 (RSP3C) could allow an unauthenticated, adjacent attacker to trigger a denial of service (DoS) condition. This vulnerability is due to improper memory management when Cisco IOS XE Software is processing Address Resolution Protocol (ARP) messages. An attacker could exploit this vulnerability by sending crafted ARP messages at a high ... A vulnerability in the Cisco Express Forwarding functionality of Cisco IOS XE Software for Cisco ASR 903 Aggregation Services Routers with Route Switch Processor 3 (RSP3C) could allow an unauthenticated, adjacent attacker to trigger a denial of service (DoS) condition. This vulnerability is due to improper memory management when Cisco IOS XE Software is processing Address Resolution Protocol (ARP) messages. An attacker could exploit this vulnerability by sending crafted ARP messages at a high rate over a period of time to an affected device. A successful exploit could allow the attacker to exhaust system resources, which eventually triggers a reload of the active route switch processor (RSP). If a redundant RSP is not present, the router reloads.

Show More

A vulnerability in the CLI of Cisco IOS XE Software could allow an authenticated, local attacker with privilege level 15 to elevate privileges to root on the underlying operating system of an affected device. This vulnerability is due to insufficient input validation when processing specific configuration commands. An attacker could exploit this vulnerability by including crafted input in specific configuration commands. A successful exploit could allow the attacker to elevate privileges to r ... A vulnerability in the CLI of Cisco IOS XE Software could allow an authenticated, local attacker with privilege level 15 to elevate privileges to root on the underlying operating system of an affected device. This vulnerability is due to insufficient input validation when processing specific configuration commands. An attacker could exploit this vulnerability by including crafted input in specific configuration commands. A successful exploit could allow the attacker to elevate privileges to root on the underlying operating system of an affected device. The security impact rating (SIR) of this advisory has been raised to High because an attacker could gain access to the underlying operating system of the affected device and perform potentially undetected actions. Note: The attacker must have privileges to enter configuration mode on the affected device. This is usually referred to as privilege level 15.

Show More

A vulnerability in the NETCONF feature of Cisco IOS XE Software could allow an authenticated, remote attacker to elevate privileges to root on an affected device. This vulnerability is due to improper validation of user-supplied input. An attacker could exploit this vulnerability by sending crafted input over NETCONF to an affected device. A successful exploit could allow the attacker to elevate privileges from Administrator to root.

A vulnerability in the SSH implementation of Cisco IOS Software and Cisco IOS XE Software could allow an authenticated, remote attacker to cause an affected device to reload. This vulnerability is due to improper handling of resources during an exceptional situation. An attacker could exploit this vulnerability by continuously connecting to an affected device and sending specific SSH requests. A successful exploit could allow the attacker to cause the affected device to reload.

A vulnerability in the SNMP implementation of could allow an authenticated, remote attacker to cause a reload of the affected system or to remotely execute code. An attacker could exploit this vulnerability by sending a crafted SNMP packet to the affected device.  The vulnerability is due to a buffer overflow in the affected code area. The vulnerability affects all versions of SNMP (versions 1, 2c, and 3). The attacker must know the SNMP read only community string (SNMP version 2c or ... A vulnerability in the SNMP implementation of could allow an authenticated, remote attacker to cause a reload of the affected system or to remotely execute code. An attacker could exploit this vulnerability by sending a crafted SNMP packet to the affected device.  The vulnerability is due to a buffer overflow in the affected code area. The vulnerability affects all versions of SNMP (versions 1, 2c, and 3). The attacker must know the SNMP read only community string (SNMP version 2c or earlier) or the user credentials (SNMPv3). An exploit could allow the attacker to execute arbitrary code and obtain full control of the system or to cause a reload of the affected system. Only traffic directed to the affected system can be used to exploit this vulnerability.

Show More

A vulnerability in the Wireless Network Control daemon (wncd) of Cisco IOS XE Software for Wireless LAN Controllers (WLCs) could allow an unauthenticated, adjacent wireless attacker to cause a denial of service (DoS) condition. This vulnerability is due to improper memory management. An attacker could exploit this vulnerability by sending a series of IPv6 network requests from an associated wireless IPv6 client to an affected device. To associate a client to a device, an attacker may first ne ... A vulnerability in the Wireless Network Control daemon (wncd) of Cisco IOS XE Software for Wireless LAN Controllers (WLCs) could allow an unauthenticated, adjacent wireless attacker to cause a denial of service (DoS) condition. This vulnerability is due to improper memory management. An attacker could exploit this vulnerability by sending a series of IPv6 network requests from an associated wireless IPv6 client to an affected device. To associate a client to a device, an attacker may first need to authenticate to the network, or associate freely in the case of a configured open network. A successful exploit could allow the attacker to cause the wncd process to consume available memory and eventually cause the device to stop responding, resulting in a DoS condition.

Show More

A vulnerability in the multicast DNS (mDNS) gateway feature of Cisco IOS XE Software for Wireless LAN Controllers (WLCs) could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition. This vulnerability is due to improper management of mDNS client entries. An attacker could exploit this vulnerability by connecting to the wireless network and sending a continuous stream of specific mDNS packets. A successful exploit could allow the attacker to cause the wireles ... A vulnerability in the multicast DNS (mDNS) gateway feature of Cisco IOS XE Software for Wireless LAN Controllers (WLCs) could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition. This vulnerability is due to improper management of mDNS client entries. An attacker could exploit this vulnerability by connecting to the wireless network and sending a continuous stream of specific mDNS packets. A successful exploit could allow the attacker to cause the wireless controller to have high CPU utilization, which could lead to access points (APs) losing their connection to the controller and result in a DoS condition.

Show More

A vulnerability in the Two-Way Active Measurement Protocol (TWAMP) server feature of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause the affected device to reload, resulting in a denial of service (DoS) condition. For Cisco IOS XR Software, this vulnerability could cause the ipsla_ippm_server process to reload unexpectedly if debugs are enabled. This vulnerability is due to out-of-bounds array access when processing specially crafted ... A vulnerability in the Two-Way Active Measurement Protocol (TWAMP) server feature of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause the affected device to reload, resulting in a denial of service (DoS) condition. For Cisco IOS XR Software, this vulnerability could cause the ipsla_ippm_server process to reload unexpectedly if debugs are enabled. This vulnerability is due to out-of-bounds array access when processing specially crafted TWAMP control packets. An attacker could exploit this vulnerability by sending crafted TWAMP control packets to an affected device. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition. Note: For Cisco IOS XR Software, only the ipsla_ippm_server process reloads unexpectedly and only when debugs are enabled. The vulnerability details for Cisco IOS XR Software are as follows:    Security Impact Rating (SIR): Low    CVSS Base Score: 3.7    CVSS Vector: CVSS:3.1/AV:N/AC:H/PR:N/UI:N/S:U/C:N/I:N/A:L

Show More

A vulnerability in the lobby ambassador web interface of Cisco IOS XE Wireless Controller Software could allow an authenticated, remote attacker to remove arbitrary users that are defined on an affected device. This vulnerability is due to insufficient access control of actions executed by lobby ambassador users. An attacker could exploit this vulnerability by logging in to an affected device with a lobby ambassador user account and sending crafted HTTP requests to the API. A successful explo ... A vulnerability in the lobby ambassador web interface of Cisco IOS XE Wireless Controller Software could allow an authenticated, remote attacker to remove arbitrary users that are defined on an affected device. This vulnerability is due to insufficient access control of actions executed by lobby ambassador users. An attacker could exploit this vulnerability by logging in to an affected device with a lobby ambassador user account and sending crafted HTTP requests to the API. A successful exploit could allow the attacker to delete arbitrary user accounts on the device, including users with administrative privileges. Note: This vulnerability is exploitable only if the attacker obtains the credentials for a lobby ambassador account. This account is not configured by default.

Show More

A vulnerability in the bootstrap loading of Cisco IOS XE Software could allow an authenticated, local attacker to write arbitrary files to an affected system. This vulnerability is due to insufficient input validation of the bootstrap file that is read by the system software when a device is first deployed in SD-WAN mode or when an administrator configures SD-Routing on the device. An attacker could exploit this vulnerability by modifying a bootstrap file generated by Cisco Catalyst SD-WAN Ma ... A vulnerability in the bootstrap loading of Cisco IOS XE Software could allow an authenticated, local attacker to write arbitrary files to an affected system. This vulnerability is due to insufficient input validation of the bootstrap file that is read by the system software when a device is first deployed in SD-WAN mode or when an administrator configures SD-Routing on the device. An attacker could exploit this vulnerability by modifying a bootstrap file generated by Cisco Catalyst SD-WAN Manager, loading it into the device flash, and then either reloading the device in a green field deployment in SD-WAN mode or configuring the device with SD-Routing. A successful exploit could allow the attacker to perform arbitrary file writes to the underlying operating system.

Show More

A vulnerability in the Unified Threat Defense (UTD) configuration CLI of Cisco IOS XE Software could allow an authenticated, local attacker to execute arbitrary commands as root on the underlying host operating system. To exploit this vulnerability, an attacker must have level 15 privileges on the affected device. This vulnerability is due to insufficient input validation. An attacker could exploit this vulnerability by submitting a crafted CLI command to an affected device. A successful exp ... A vulnerability in the Unified Threat Defense (UTD) configuration CLI of Cisco IOS XE Software could allow an authenticated, local attacker to execute arbitrary commands as root on the underlying host operating system. To exploit this vulnerability, an attacker must have level 15 privileges on the affected device. This vulnerability is due to insufficient input validation. An attacker could exploit this vulnerability by submitting a crafted CLI command to an affected device. A successful exploit could allow the attacker to execute arbitrary commands as root on the underlying operating system.

Show More

A vulnerability in auxiliary asynchronous port (AUX) functions of Cisco IOS XE Software could allow an authenticated, local attacker to cause an affected device to reload or stop responding. This vulnerability is due to the incorrect handling of specific ingress traffic when flow control hardware is enabled on the AUX port. An attacker could exploit this vulnerability by reverse telnetting to the AUX port and sending specific data after connecting. A successful exploit could allow the attacke ... A vulnerability in auxiliary asynchronous port (AUX) functions of Cisco IOS XE Software could allow an authenticated, local attacker to cause an affected device to reload or stop responding. This vulnerability is due to the incorrect handling of specific ingress traffic when flow control hardware is enabled on the AUX port. An attacker could exploit this vulnerability by reverse telnetting to the AUX port and sending specific data after connecting. A successful exploit could allow the attacker to cause the device to reset or stop responding, resulting in a denial of service (DoS) condition.

Show More

A vulnerability in the Locator ID Separation Protocol (LISP) feature of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause an affected device to reload. This vulnerability is due to the incorrect handling of LISP packets. An attacker could exploit this vulnerability by sending a crafted LISP packet to an affected device. A successful exploit could allow the attacker to cause the device to reload, resulting in a denial of service (DoS) conditi ... A vulnerability in the Locator ID Separation Protocol (LISP) feature of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause an affected device to reload. This vulnerability is due to the incorrect handling of LISP packets. An attacker could exploit this vulnerability by sending a crafted LISP packet to an affected device. A successful exploit could allow the attacker to cause the device to reload, resulting in a denial of service (DoS) condition. Note: This vulnerability could be exploited over either IPv4 or IPv6 transport.

Show More

A vulnerability in the IPv4 Software-Defined Access (SD-Access) fabric edge node feature of Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause high CPU utilization and stop all traffic processing, resulting in a denial of service (DoS) condition on an affected device. This vulnerability is due to improper handling of certain IPv4 packets. An attacker could exploit this vulnerability by sending certain IPv4 packets to an affected device. A successful exploit could a ... A vulnerability in the IPv4 Software-Defined Access (SD-Access) fabric edge node feature of Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause high CPU utilization and stop all traffic processing, resulting in a denial of service (DoS) condition on an affected device. This vulnerability is due to improper handling of certain IPv4 packets. An attacker could exploit this vulnerability by sending certain IPv4 packets to an affected device. A successful exploit could allow the attacker to cause the device to exhaust CPU resources and stop processing traffic, resulting in a DoS condition.

Show More

A vulnerability in the data model interface (DMI) services of Cisco IOS XE Software could allow an unauthenticated, remote attacker to access resources that should have been protected by a configured IPv4 access control list (ACL). This vulnerability is due to improper handling of error conditions when a successfully authorized device administrator updates an IPv4 ACL using the NETCONF or RESTCONF protocol, and the update would reorder access control entries (ACEs) in the updated ACL. An atta ... A vulnerability in the data model interface (DMI) services of Cisco IOS XE Software could allow an unauthenticated, remote attacker to access resources that should have been protected by a configured IPv4 access control list (ACL). This vulnerability is due to improper handling of error conditions when a successfully authorized device administrator updates an IPv4 ACL using the NETCONF or RESTCONF protocol, and the update would reorder access control entries (ACEs) in the updated ACL. An attacker could exploit this vulnerability by accessing resources that should have been protected across an affected device.

Show More

A vulnerability in the CLI of Cisco IOS XE Software could allow an authenticated, low-privileged, local attacker to access WLAN configuration details including passwords. This vulnerability is due to improper privilege checks. An attacker could exploit this vulnerability by using the show and show tech wireless CLI commands to access configuration details, including passwords. A successful exploit could allow the attacker to access configuration details that they are not authorized to access.

A vulnerability in the IKEv1 fragmentation code of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause a heap overflow, resulting in an affected device reloading. This vulnerability exists because crafted, fragmented IKEv1 packets are not properly reassembled. An attacker could exploit this vulnerability by sending crafted UDP packets to an affected system. A successful exploit could allow the attacker to cause the affected device to reload, r ... A vulnerability in the IKEv1 fragmentation code of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause a heap overflow, resulting in an affected device reloading. This vulnerability exists because crafted, fragmented IKEv1 packets are not properly reassembled. An attacker could exploit this vulnerability by sending crafted UDP packets to an affected system. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition. Note: Only traffic that is directed to the affected system can be used to exploit this vulnerability. This vulnerability can be triggered by IPv4 and IPv6 traffic.

Show More

A vulnerability in the DHCP snooping security feature of Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause a full interface queue wedge, which could result in a denial of service (DoS) condition. This vulnerability is due to improper handling of DHCP request packets. An attacker could exploit this vulnerability by sending DHCP request packets to an affected device. A successful exploit could allow the attacker to cause packets to wedge in the queue, creating a DoS ... A vulnerability in the DHCP snooping security feature of Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause a full interface queue wedge, which could result in a denial of service (DoS) condition. This vulnerability is due to improper handling of DHCP request packets. An attacker could exploit this vulnerability by sending DHCP request packets to an affected device. A successful exploit could allow the attacker to cause packets to wedge in the queue, creating a DoS condition for downstream devices of the affected system and requiring that the system restart to drain the queue. Note: This vulnerability can be exploited with either unicast or broadcast DHCP packets on a VLAN that does not have DHCP snooping enabled.

Show More

A vulnerability in the web-based management interface of the Wireless LAN Controller feature of Cisco IOS XE Software could allow an authenticated, remote attacker with a lobby ambassador user account to perform a command injection attack against an affected device. This vulnerability is due to insufficient input validation. An attacker could exploit this vulnerability by sending crafted input to the web-based management interface. A successful exploit could allow the attacker to execute arbi ... A vulnerability in the web-based management interface of the Wireless LAN Controller feature of Cisco IOS XE Software could allow an authenticated, remote attacker with a lobby ambassador user account to perform a command injection attack against an affected device. This vulnerability is due to insufficient input validation. An attacker could exploit this vulnerability by sending crafted input to the web-based management interface. A successful exploit could allow the attacker to execute arbitrary Cisco IOS XE Software CLI commands with privilege level 15. Note: This vulnerability is exploitable only if the attacker obtains the credentials for a lobby ambassador account. This account is not configured by default.

Show More

A vulnerability in the web-based management interface of Cisco IOS XE Software could allow an authenticated, low-privileged, remote attacker to perform an injection attack against an affected device.r This vulnerability is due to insufficient input validation. An attacker could exploit this vulnerability by sending crafted input to the web-based management interface. A successful exploit could allow the attacker to read files from the underlying operating system.

A vulnerability in the web-based management interface of Cisco IOS XE Software could allow an authenticated, low-privileged, remote attacker to perform an injection attack against an affected device. This vulnerability is due to insufficient input validation. An attacker could exploit this vulnerability by sending crafted input to the web-based management interface. A successful exploit could allow the attacker to read limited files from the underlying operating system or clear the syslog an ... A vulnerability in the web-based management interface of Cisco IOS XE Software could allow an authenticated, low-privileged, remote attacker to perform an injection attack against an affected device. This vulnerability is due to insufficient input validation. An attacker could exploit this vulnerability by sending crafted input to the web-based management interface. A successful exploit could allow the attacker to read limited files from the underlying operating system or clear the syslog and licensing logs on the affected device.

Show More

A vulnerability in the web-based management interface of Cisco IOS XE Software could allow an unauthenticated, remote attacker to perform a CSRF attack and execute commands on the CLI of an affected device. This vulnerability is due to insufficient CSRF protections for the web-based management interface of an affected device. An attacker could exploit this vulnerability by persuading an already authenticated user to follow a crafted link. A successful exploit could allow the attacker to clea ... A vulnerability in the web-based management interface of Cisco IOS XE Software could allow an unauthenticated, remote attacker to perform a CSRF attack and execute commands on the CLI of an affected device. This vulnerability is due to insufficient CSRF protections for the web-based management interface of an affected device. An attacker could exploit this vulnerability by persuading an already authenticated user to follow a crafted link. A successful exploit could allow the attacker to clear the syslog, parser, and licensing logs on the affected device if the targeted user has privileges to clear those logs.

Show More

A vulnerability in the Cisco IOx application hosting environment of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause the Cisco IOx application hosting environment to stop responding, resulting in a denial of service (DoS) condition. This vulnerability is due to the improper handling of HTTP requests. An attacker could exploit this vulnerability by sending crafted HTTP requests to an affected device. A successful exploit could allow the atta ... A vulnerability in the Cisco IOx application hosting environment of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause the Cisco IOx application hosting environment to stop responding, resulting in a denial of service (DoS) condition. This vulnerability is due to the improper handling of HTTP requests. An attacker could exploit this vulnerability by sending crafted HTTP requests to an affected device. A successful exploit could allow the attacker to cause the Cisco IOx application hosting environment to stop responding. The IOx process will need to be manually restarted to recover services.

Show More

A vulnerability in the CLI of Cisco IOS XE Software could allow an authenticated, local attacker with privilege level 15 to elevate privileges to root on the underlying operating system of an affected device. This vulnerability is due to insufficient input validation when processing specific configuration commands. An attacker could exploit this vulnerability by including crafted input in specific configuration commands. A successful exploit could allow the attacker to elevate privileges to r ... A vulnerability in the CLI of Cisco IOS XE Software could allow an authenticated, local attacker with privilege level 15 to elevate privileges to root on the underlying operating system of an affected device. This vulnerability is due to insufficient input validation when processing specific configuration commands. An attacker could exploit this vulnerability by including crafted input in specific configuration commands. A successful exploit could allow the attacker to elevate privileges to root on the underlying operating system of an affected device. The security impact rating (SIR) of this advisory has been raised to High because an attacker could gain access to the underlying operating system of the affected device and perform potentially undetected actions. Note: The attacker must have privileges to enter configuration mode on the affected device. This is usually referred to as privilege level 15.

Show More

A vulnerability in the packet filtering features of Cisco IOS XE SD-WAN Software could allow an unauthenticated, remote attacker to bypass Layer 3 and Layer 4 traffic filters. This vulnerability is due to improper traffic filtering conditions on an affected device. An attacker could exploit this vulnerability by sending a crafted packet to the affected device. A successful exploit could allow the attacker to bypass the Layer 3 and Layer 4 traffic filters and inject a crafted packet into the ... A vulnerability in the packet filtering features of Cisco IOS XE SD-WAN Software could allow an unauthenticated, remote attacker to bypass Layer 3 and Layer 4 traffic filters. This vulnerability is due to improper traffic filtering conditions on an affected device. An attacker could exploit this vulnerability by sending a crafted packet to the affected device. A successful exploit could allow the attacker to bypass the Layer 3 and Layer 4 traffic filters and inject a crafted packet into the network.

Show More

A vulnerability in Cisco IOS XE Wireless Controller Software could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to insufficient input validation of access point (AP) Cisco Discovery Protocol (CDP) neighbor reports when they are processed by the wireless controller. An attacker could exploit this vulnerability by sending a crafted CDP packet to an AP. A successful exploit could allow the attacker to ca ... A vulnerability in Cisco IOS XE Wireless Controller Software could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to insufficient input validation of access point (AP) Cisco Discovery Protocol (CDP) neighbor reports when they are processed by the wireless controller. An attacker could exploit this vulnerability by sending a crafted CDP packet to an AP. A successful exploit could allow the attacker to cause an unexpected reload of the wireless controller that is managing the AP, resulting in a DoS condition that affects the wireless network.

Show More

A vulnerability in the CLI of Cisco IOS XE Software could allow an authenticated, local attacker with privilege level 15 to elevate privileges to root on the underlying operating system of an affected device. This vulnerability is due to insufficient input validation when processing specific configuration commands. An attacker could exploit this vulnerability by including crafted input in specific configuration commands. A successful exploit could allow the attacker to elevate privileges to r ... A vulnerability in the CLI of Cisco IOS XE Software could allow an authenticated, local attacker with privilege level 15 to elevate privileges to root on the underlying operating system of an affected device. This vulnerability is due to insufficient input validation when processing specific configuration commands. An attacker could exploit this vulnerability by including crafted input in specific configuration commands. A successful exploit could allow the attacker to elevate privileges to root on the underlying operating system of an affected device. The security impact rating (SIR) of this advisory has been raised to High because an attacker could gain access to the underlying operating system of the affected device and perform potentially undetected actions. Note: The attacker must have privileges to enter configuration mode on the affected device. This is usually referred to as privilege level 15.

Show More

A vulnerability in the CLI of Cisco IOS XE Software could allow an authenticated, local attacker with privilege level 15 to elevate privileges to root on the underlying operating system of an affected device. This vulnerability is due to insufficient input validation when processing specific configuration commands. An attacker could exploit this vulnerability by including crafted input in specific configuration commands. A successful exploit could allow the attacker to elevate privileges to r ... A vulnerability in the CLI of Cisco IOS XE Software could allow an authenticated, local attacker with privilege level 15 to elevate privileges to root on the underlying operating system of an affected device. This vulnerability is due to insufficient input validation when processing specific configuration commands. An attacker could exploit this vulnerability by including crafted input in specific configuration commands. A successful exploit could allow the attacker to elevate privileges to root on the underlying operating system of an affected device. The security impact rating (SIR) of this advisory has been raised to High because an attacker could gain access to the underlying operating system of the affected device and perform potentially undetected actions. Note: The attacker must have privileges to enter configuration mode on the affected device. This is usually referred to as privilege level 15.

Show More

A vulnerability in the CLI of Cisco IOS XE Software could allow an authenticated, local attacker with privilege level 15 to elevate privileges to root on the underlying operating system of an affected device. This vulnerability is due to insufficient input validation when processing specific configuration commands. An attacker could exploit this vulnerability by including crafted input in specific configuration commands. A successful exploit could allow the attacker to elevate privileges to r ... A vulnerability in the CLI of Cisco IOS XE Software could allow an authenticated, local attacker with privilege level 15 to elevate privileges to root on the underlying operating system of an affected device. This vulnerability is due to insufficient input validation when processing specific configuration commands. An attacker could exploit this vulnerability by including crafted input in specific configuration commands. A successful exploit could allow the attacker to elevate privileges to root on the underlying operating system of an affected device. The security impact rating (SIR) of this advisory has been raised to High because an attacker could gain access to the underlying operating system of the affected device and perform potentially undetected actions. Note: The attacker must have privileges to enter configuration mode on the affected device. This is usually referred to as privilege level 15.

Show More

A vulnerability in the SNMP subsystem of Cisco IOS Software and Cisco IOS XE Software could allow an authenticated, remote attacker to cause a DoS condition on an affected device. This vulnerability is due to improper error handling when parsing SNMP requests. An attacker could exploit this vulnerability by sending a crafted SNMP request to an affected device. A successful exploit could allow the attacker to cause the device to reload unexpectedly, resulting in a DoS condition.  This vu ... A vulnerability in the SNMP subsystem of Cisco IOS Software and Cisco IOS XE Software could allow an authenticated, remote attacker to cause a DoS condition on an affected device. This vulnerability is due to improper error handling when parsing SNMP requests. An attacker could exploit this vulnerability by sending a crafted SNMP request to an affected device. A successful exploit could allow the attacker to cause the device to reload unexpectedly, resulting in a DoS condition.  This vulnerability affects SNMP versions 1, 2c, and 3. To exploit this vulnerability through SNMP v2c or earlier, the attacker must know a valid read-write or read-only SNMP community string for the affected system. To exploit this vulnerability through SNMP v3, the attacker must have valid SNMP user credentials for the affected system.

Show More

A vulnerability in the SNMP subsystem of Cisco IOS Software and Cisco IOS XE Software could allow an authenticated, remote attacker to cause a DoS condition on an affected device. This vulnerability is due to improper error handling when parsing SNMP requests. An attacker could exploit this vulnerability by sending a crafted SNMP request to an affected device. A successful exploit could allow the attacker to cause the device to reload unexpectedly, resulting in a DoS condition.  This vu ... A vulnerability in the SNMP subsystem of Cisco IOS Software and Cisco IOS XE Software could allow an authenticated, remote attacker to cause a DoS condition on an affected device. This vulnerability is due to improper error handling when parsing SNMP requests. An attacker could exploit this vulnerability by sending a crafted SNMP request to an affected device. A successful exploit could allow the attacker to cause the device to reload unexpectedly, resulting in a DoS condition.  This vulnerability affects SNMP versions 1, 2c, and 3. To exploit this vulnerability through SNMP v2c or earlier, the attacker must know a valid read-write or read-only SNMP community string for the affected system. To exploit this vulnerability through SNMP v3, the attacker must have valid SNMP user credentials for the affected system.

Show More

A vulnerability in the SNMP subsystem of Cisco IOS Software, Cisco IOS XE Software, and Cisco IOS XR Software could allow an authenticated, remote attacker to cause a DoS condition on an affected device. This vulnerability is due to improper error handling when parsing SNMP requests. An attacker could exploit this vulnerability by sending a crafted SNMP request to an affected device. For Cisco IOS and IOS XE Software, a successful exploit could allow the attacker to cause the device to reload ... A vulnerability in the SNMP subsystem of Cisco IOS Software, Cisco IOS XE Software, and Cisco IOS XR Software could allow an authenticated, remote attacker to cause a DoS condition on an affected device. This vulnerability is due to improper error handling when parsing SNMP requests. An attacker could exploit this vulnerability by sending a crafted SNMP request to an affected device. For Cisco IOS and IOS XE Software, a successful exploit could allow the attacker to cause the device to reload unexpectedly, resulting in a DoS condition. For Cisco IOS XR Software, a successful exploit could allow the attacker to cause the SNMP process to restart, resulting in an interrupted SNMP response from an affected device. Devices that are running Cisco IOS XR Software will not reload.  This vulnerability affects SNMP versions 1, 2c, and 3. To exploit this vulnerability through SNMP v2c or earlier, the attacker must know a valid read-write or read-only SNMP community string for the affected system. To exploit this vulnerability through SNMP v3, the attacker must have valid SNMP user credentials for the affected system.

Show More

A vulnerability in the SNMP subsystem of Cisco IOS Software and Cisco IOS XE Software could allow an authenticated, remote attacker to cause a DoS condition on an affected device. This vulnerability is due to improper error handling when parsing SNMP requests. An attacker could exploit this vulnerability by sending a crafted SNMP request to an affected device. A successful exploit could allow the attacker to cause the device to reload unexpectedly, resulting in a DoS condition.  This vu ... A vulnerability in the SNMP subsystem of Cisco IOS Software and Cisco IOS XE Software could allow an authenticated, remote attacker to cause a DoS condition on an affected device. This vulnerability is due to improper error handling when parsing SNMP requests. An attacker could exploit this vulnerability by sending a crafted SNMP request to an affected device. A successful exploit could allow the attacker to cause the device to reload unexpectedly, resulting in a DoS condition.  This vulnerability affects SNMP versions 1, 2c, and 3. To exploit this vulnerability through SNMP v2c or earlier, the attacker must know a valid read-write or read-only SNMP community string for the affected system. To exploit this vulnerability through SNMP v3, the attacker must have valid SNMP user credentials for the affected system.

Show More

A vulnerability in the SNMP subsystem of Cisco IOS Software and Cisco IOS XE Software could allow an authenticated, remote attacker to cause a DoS condition on an affected device. This vulnerability is due to improper error handling when parsing SNMP requests. An attacker could exploit this vulnerability by sending a crafted SNMP request to an affected device. A successful exploit could allow the attacker to cause the device to reload unexpectedly, resulting in a DoS condition.  This vu ... A vulnerability in the SNMP subsystem of Cisco IOS Software and Cisco IOS XE Software could allow an authenticated, remote attacker to cause a DoS condition on an affected device. This vulnerability is due to improper error handling when parsing SNMP requests. An attacker could exploit this vulnerability by sending a crafted SNMP request to an affected device. A successful exploit could allow the attacker to cause the device to reload unexpectedly, resulting in a DoS condition.  This vulnerability affects SNMP versions 1, 2c, and 3. To exploit this vulnerability through SNMP v2c or earlier, the attacker must know a valid read-write or read-only SNMP community string for the affected system. To exploit this vulnerability through SNMP v3, the attacker must have valid SNMP user credentials for the affected system.

Show More

A vulnerability in the SNMP subsystem of Cisco IOS Software and Cisco IOS XE Software could allow an authenticated, remote attacker to cause a DoS condition on an affected device. This vulnerability is due to improper error handling when parsing SNMP requests. An attacker could exploit this vulnerability by sending a crafted SNMP request to an affected device. A successful exploit could allow the attacker to cause the device to reload unexpectedly, resulting in a DoS condition.  This vu ... A vulnerability in the SNMP subsystem of Cisco IOS Software and Cisco IOS XE Software could allow an authenticated, remote attacker to cause a DoS condition on an affected device. This vulnerability is due to improper error handling when parsing SNMP requests. An attacker could exploit this vulnerability by sending a crafted SNMP request to an affected device. A successful exploit could allow the attacker to cause the device to reload unexpectedly, resulting in a DoS condition.  This vulnerability affects SNMP versions 1, 2c, and 3. To exploit this vulnerability through SNMP v2c or earlier, the attacker must know a valid read-write or read-only SNMP community string for the affected system. To exploit this vulnerability through SNMP v3, the attacker must have valid SNMP user credentials for the affected system.

Show More

A vulnerability in the SNMP subsystem of Cisco IOS Software and Cisco IOS XE Software could allow an authenticated, remote attacker to cause a DoS condition on an affected device. This vulnerability is due to improper error handling when parsing SNMP requests. An attacker could exploit this vulnerability by sending a crafted SNMP request to an affected device. A successful exploit could allow the attacker to cause the device to reload unexpectedly, resulting in a DoS condition.  This vu ... A vulnerability in the SNMP subsystem of Cisco IOS Software and Cisco IOS XE Software could allow an authenticated, remote attacker to cause a DoS condition on an affected device. This vulnerability is due to improper error handling when parsing SNMP requests. An attacker could exploit this vulnerability by sending a crafted SNMP request to an affected device. A successful exploit could allow the attacker to cause the device to reload unexpectedly, resulting in a DoS condition.  This vulnerability affects SNMP versions 1, 2c, and 3. To exploit this vulnerability through SNMP v2c or earlier, the attacker must know a valid read-write or read-only SNMP community string for the affected system. To exploit this vulnerability through SNMP v3, the attacker must have valid SNMP user credentials for the affected system.

Show More

A vulnerability in the IKEv1 fragmentation code of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause a heap underflow, resulting in an affected device reloading. This vulnerability exists because crafted, fragmented IKEv1 packets are not properly reassembled. An attacker could exploit this vulnerability by sending crafted UDP packets to an affected system. A successful exploit could allow the attacker to cause the affected device to reload, ... A vulnerability in the IKEv1 fragmentation code of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause a heap underflow, resulting in an affected device reloading. This vulnerability exists because crafted, fragmented IKEv1 packets are not properly reassembled. An attacker could exploit this vulnerability by sending crafted UDP packets to an affected system. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a denial of service (DoS) condition. Note: Only traffic that is directed to the affected system can be used to exploit this vulnerability. This vulnerability can be triggered by IPv4 and IPv6 traffic..

Show More

A vulnerability in the Out-of-Band Access Point (AP) Image Download, the Clean Air Spectral Recording, and the client debug bundles features of Cisco IOS XE Software for Wireless LAN Controllers (WLCs) could allow an unauthenticated, remote attacker to upload arbitrary files to an affected system. This vulnerability is due to the presence of a hard-coded JSON Web Token (JWT) on an affected system. An attacker could exploit this vulnerability by sending crafted HTTPS requests to the AP file u ... A vulnerability in the Out-of-Band Access Point (AP) Image Download, the Clean Air Spectral Recording, and the client debug bundles features of Cisco IOS XE Software for Wireless LAN Controllers (WLCs) could allow an unauthenticated, remote attacker to upload arbitrary files to an affected system. This vulnerability is due to the presence of a hard-coded JSON Web Token (JWT) on an affected system. An attacker could exploit this vulnerability by sending crafted HTTPS requests to the AP file upload interface. A successful exploit could allow the attacker to upload files, perform path traversal, and execute arbitrary commands with root privileges.

Show More