Vulnerabilities (CVE)

When DNS filtering is enabled on Juniper Networks Junos MX Series with one of the following cards MS-PIC, MS-MIC or MS-MPC, an incoming stream of packets processed by the Multiservices PIC Management Daemon (mspmand) process, responsible for managing "URL Filtering service", may crash, causing the Services PIC to restart. While the Services PIC is restarting, all PIC services including DNS filtering service (DNS sink holing) will be bypassed until the Services PIC completes its boot process. Thi ... When DNS filtering is enabled on Juniper Networks Junos MX Series with one of the following cards MS-PIC, MS-MIC or MS-MPC, an incoming stream of packets processed by the Multiservices PIC Management Daemon (mspmand) process, responsible for managing "URL Filtering service", may crash, causing the Services PIC to restart. While the Services PIC is restarting, all PIC services including DNS filtering service (DNS sink holing) will be bypassed until the Services PIC completes its boot process. This vulnerability might allow an attacker to cause an extended Denial of Service (DoS) attack against the device and to cause clients to be vulnerable to DNS based attacks by malicious DNS servers when they send DNS requests through the device. As a result, devices which were once protected by the DNS Filtering service are no longer protected and at risk of exploitation. This issue affects Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S8; 18.3 versions prior to 18.3R3-S1; 18.4 versions prior to 18.4R3; 19.1 versions prior to 19.1R3; 19.2 versions prior to 19.2R2; 19.3 versions prior to 19.3R3. This issue does not affect Juniper Networks Junos OS 17.4, 18.1, and 18.2.

Show More

On SRX Series devices, a vulnerability in the key-management-daemon (kmd) daemon of Juniper Networks Junos OS allows an attacker to spoof packets targeted to IPSec peers before a security association (SA) is established thereby causing a failure to set up the IPSec channel. Sustained receipt of these spoofed packets can cause a sustained Denial of Service (DoS) condition. This issue affects IPv4 and IPv6 implementations. This issue affects Juniper Networks Junos OS on SRX Series: 12.3X48 version ... On SRX Series devices, a vulnerability in the key-management-daemon (kmd) daemon of Juniper Networks Junos OS allows an attacker to spoof packets targeted to IPSec peers before a security association (SA) is established thereby causing a failure to set up the IPSec channel. Sustained receipt of these spoofed packets can cause a sustained Denial of Service (DoS) condition. This issue affects IPv4 and IPv6 implementations. This issue affects Juniper Networks Junos OS on SRX Series: 12.3X48 versions prior to 12.3X48-D90; 15.1X49 versions prior to 15.1X49-D190; 17.4 versions prior to 17.4R2-S9, 17.4R3; 18.1 versions prior to 18.1R3-S9; 18.2 versions prior to 18.2R3; 18.3 versions prior to 18.3R1-S7, 18.3R2-S3, 18.3R3; 18.4 versions prior to 18.4R1-S6, 18.4R2-S3, 18.4R3; 19.1 versions prior to 19.1R1-S4, 19.1R2. This issue does not affect 12.3 or 15.1 releases which are non-SRX Series releases.

Show More

The DHCPv6 Relay-Agent service, part of the Juniper Enhanced jdhcpd daemon shipped with Juniper Networks Junos OS has an Improper Input Validation vulnerability which will result in a Denial of Service (DoS) condition when a DHCPv6 client sends a specific DHPCv6 message allowing an attacker to potentially perform a Remote Code Execution (RCE) attack on the target device. Continuous receipt of the specific DHCPv6 client message will result in an extended Denial of Service (DoS) condition. If adja ... The DHCPv6 Relay-Agent service, part of the Juniper Enhanced jdhcpd daemon shipped with Juniper Networks Junos OS has an Improper Input Validation vulnerability which will result in a Denial of Service (DoS) condition when a DHCPv6 client sends a specific DHPCv6 message allowing an attacker to potentially perform a Remote Code Execution (RCE) attack on the target device. Continuous receipt of the specific DHCPv6 client message will result in an extended Denial of Service (DoS) condition. If adjacent devices are also configured to relay DHCP packets, and are not affected by this issue and simply transparently forward unprocessed client DHCPv6 messages, then the attack vector can be a Network-based attack, instead of an Adjacent-device attack. No other DHCP services are affected. Receipt of the packet without configuration of the DHCPv6 Relay-Agent service, will not result in exploitability of this issue. This issue affects Juniper Networks Junos OS: 12.3 versions prior to 12.3R12-S15; 12.3X48 versions prior to 12.3X48-D95; 14.1X53 versions prior to 14.1X53-D53; 15.1 versions prior to 15.1R7-S6; 15.1X49 versions prior to 15.1X49-D200; 15.1X53 versions prior to 15.1X53-D593; 16.1 versions prior to 16.1R7-S7; 16.2 versions prior to 16.2R2-S11; 17.1 versions prior to 17.1R2-S11, 17.1R3-S2; 17.2 versions prior to 17.2R3-S3; 17.2X75 versions prior to 17.2X75-D44; 17.3 versions prior to 17.3R3-S7; 17.4 versions prior to 17.4R2-S9, 17.4R3; 18.1 versions prior to 18.1R3-S9; 18.2 versions prior to 18.2R2-S6, 18.2R3-S2; 18.2X75 versions prior to 18.2X75-D12, 18.2X75-D33, 18.2X75-D435, 18.2X75-D60; 18.3 versions prior to 18.3R1-S7, 18.3R2-S3, 18.3R3-S1; 18.4 versions prior to 18.4R1-S5, 18.4R2-S3, 18.4R3; 19.1 versions prior to 19.1R1-S4, 19.1R2; 19.2 versions prior to 19.2R1-S3, 19.2R2; 19.3 versions prior to 19.3R2.

Show More

When a device running Juniper Networks Junos OS with MPC7, MPC8, or MPC9 line cards installed and the system is configured for inline IP reassembly, used by L2TP, MAP-E, GRE, and IPIP, the packet forwarding engine (PFE) will become disabled upon receipt of large packets requiring fragmentation, generating the following error messages: [LOG: Err] MQSS(0): WO: Packet Error - Error Packets 1, Connection 29 [LOG: Err] eachip_hmcif_rx_intr_handler(7259): EA[0:0]: HMCIF Rx: Injected checksum error det ... When a device running Juniper Networks Junos OS with MPC7, MPC8, or MPC9 line cards installed and the system is configured for inline IP reassembly, used by L2TP, MAP-E, GRE, and IPIP, the packet forwarding engine (PFE) will become disabled upon receipt of large packets requiring fragmentation, generating the following error messages: [LOG: Err] MQSS(0): WO: Packet Error - Error Packets 1, Connection 29 [LOG: Err] eachip_hmcif_rx_intr_handler(7259): EA[0:0]: HMCIF Rx: Injected checksum error detected on WO response - Chunk Address 0x0 [LOG: Err] MQSS(0): DRD: RORD1: CMD reorder ID error - Command 11, Reorder ID 1838, QID 0 [LOG: Err] MQSS(0): DRD: UNROLL0: HMC chunk length error in stage 5 - Chunk Address: 0x4321f3 [LOG: Err] MQSS(0): DRD: UNROLL0: HMC chunk address error in stage 5 - Chunk Address: 0x0 [LOG: Notice] Error: /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc), scope: pfe, category: functional, severity: major, module: MQSS(0), type: DRD_RORD_ENG_INT: CMD FSM State Error [LOG: Notice] Performing action cmalarm for error /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(0) with scope: pfe category: functional level: major [LOG: Notice] Performing action get-state for error /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(0) with scope: pfe category: functional level: major [LOG: Notice] Performing action disable-pfe for error /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(0) with scope: pfe category: functional level: major By continuously sending fragmented packets that cannot be reassembled, an attacker can repeatedly disable the PFE causing a sustained Denial of Service (DoS). This issue affects Juniper Networks Junos OS: 17.2 versions prior to 17.2R3-S4 on MX Series; 17.3 versions prior to 17.3R3-S8 on MX Series; 17.4 versions prior to 17.4R2-S10, 17.4R3-S2 on MX Series; 18.1 versions prior to 18.1R3-S10 on MX Series; 18.2 versions prior to 18.2R3-S3 on MX Series; 18.2X75 versions prior to 18.2X75-D41, 18.2X75-D430, 18.2X75-D65 on MX Series; 18.3 versions prior to 18.3R1-S7, 18.3R2-S4, 18.3R3-S1 on MX Series; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3 on MX Series; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3 on MX Series; 19.2 versions prior to 19.2R1-S4, 19.2R2 on MX Series; 19.3 versions prior to 19.3R2-S2, 19.3R3 on MX Series. This issue is specific to inline IP reassembly, introduced in Junos OS 17.2. Versions of Junos OS prior to 17.2 are unaffected by this vulnerability.

Show More

On Juniper Networks SRX Series with ICAP (Internet Content Adaptation Protocol) redirect service enabled, processing a malformed HTTP message can lead to a Denial of Service (DoS) or Remote Code Execution (RCE) Continued processing of this malformed HTTP message may result in an extended Denial of Service (DoS) condition. The offending HTTP message that causes this issue may originate both from the HTTP server or the HTTP client. This issue affects Juniper Networks Junos OS on SRX Series: 18.1 v ... On Juniper Networks SRX Series with ICAP (Internet Content Adaptation Protocol) redirect service enabled, processing a malformed HTTP message can lead to a Denial of Service (DoS) or Remote Code Execution (RCE) Continued processing of this malformed HTTP message may result in an extended Denial of Service (DoS) condition. The offending HTTP message that causes this issue may originate both from the HTTP server or the HTTP client. This issue affects Juniper Networks Junos OS on SRX Series: 18.1 versions prior to 18.1R3-S9 ; 18.2 versions prior to 18.2R2-S7, 18.2R3-S3; 18.3 versions prior to 18.3R1-S7, 18.3R2-S4, 18.3R3-S1; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3; 19.1 versions prior to 19.1R1-S5, 19.1R2; 19.2 versions prior to 19.2R1-S2, 19.2R2; 19.3 versions prior to 19.3R2. This issue does not affect Juniper Networks Junos OS prior to 18.1R1.

Show More

On Juniper Networks Junos OS devices, a stream of TCP packets sent to the Routing Engine (RE) may cause mbuf leak which can lead to Flexible PIC Concentrator (FPC) crash or the system to crash and restart (vmcore). This issue can be trigged by IPv4 or IPv6 and it is caused only by TCP packets. This issue is not related to any specific configuration and it affects Junos OS releases starting from 17.4R1. However, this issue does not affect Junos OS releases prior to 18.2R1 when Nonstop active rout ... On Juniper Networks Junos OS devices, a stream of TCP packets sent to the Routing Engine (RE) may cause mbuf leak which can lead to Flexible PIC Concentrator (FPC) crash or the system to crash and restart (vmcore). This issue can be trigged by IPv4 or IPv6 and it is caused only by TCP packets. This issue is not related to any specific configuration and it affects Junos OS releases starting from 17.4R1. However, this issue does not affect Junos OS releases prior to 18.2R1 when Nonstop active routing (NSR) is configured [edit routing-options nonstop-routing]. The number of mbufs is platform dependent. The following command provides the number of mbufs counter that are currently in use and maximum number of mbufs that can be allocated on a platform: user@host> show system buffers 2437/3143/5580 mbufs in use (current/cache/total) Once the device runs out of mbufs, the FPC crashes or the vmcore occurs and the device might become inaccessible requiring a manual restart. This issue affects Juniper Networks Junos OS 17.4 versions prior to 17.4R2-S11, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R2-S7, 18.2R3-S5; 18.2X75 versions prior to 18.2X75-D41, 18.2X75-D420.12, 18.2X75-D51, 18.2X75-D60, 18.2X75-D34; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3-S1; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2. Versions of Junos OS prior to 17.4R1 are unaffected by this vulnerability.

Show More

On Juniper Networks MX series, receipt of a stream of specific Layer 2 frames may cause a memory leak resulting in the packet forwarding engine (PFE) on the line card to crash and restart, causing traffic interruption. By continuously sending this stream of specific layer 2 frame, an attacker connected to the same broadcast domain can repeatedly crash the PFE, causing a prolonged Denial of Service (DoS). This issue affects Juniper Networks Junos OS on MX Series: 17.2 versions prior to 17.2R3-S4; ... On Juniper Networks MX series, receipt of a stream of specific Layer 2 frames may cause a memory leak resulting in the packet forwarding engine (PFE) on the line card to crash and restart, causing traffic interruption. By continuously sending this stream of specific layer 2 frame, an attacker connected to the same broadcast domain can repeatedly crash the PFE, causing a prolonged Denial of Service (DoS). This issue affects Juniper Networks Junos OS on MX Series: 17.2 versions prior to 17.2R3-S4; 17.2X75 versions prior to 17.2X75-D105.19; 17.3 versions prior to 17.3R3-S7; 17.4 versions prior to 17.4R1-S3, 17.4R2; 18.1 versions prior to 18.1R2. This issue does not affect Juniper Networks Junos OS releases prior to 17.2R1.

Show More

On Juniper Networks Junos MX Series with service card configured, receipt of a stream of specific packets may crash the MS-PIC component on MS-MIC or MS-MPC. By continuously sending these specific packets, an attacker can repeatedly bring down MS-PIC on MS-MIC/MS-MPC causing a prolonged Denial of Service. This issue affects MX Series devices using MS-PIC, MS-MIC or MS-MPC service cards with any service configured. This issue affects Juniper Networks Junos OS on MX Series: 17.2R2-S7; 17.3R3-S4, 1 ... On Juniper Networks Junos MX Series with service card configured, receipt of a stream of specific packets may crash the MS-PIC component on MS-MIC or MS-MPC. By continuously sending these specific packets, an attacker can repeatedly bring down MS-PIC on MS-MIC/MS-MPC causing a prolonged Denial of Service. This issue affects MX Series devices using MS-PIC, MS-MIC or MS-MPC service cards with any service configured. This issue affects Juniper Networks Junos OS on MX Series: 17.2R2-S7; 17.3R3-S4, 17.3R3-S5; 17.4R2-S4 and the subsequent SRs (17.4R2-S5, 17.4R2-S6, etc.); 17.4R3; 18.1R3-S3, 18.1R3-S4, 18.1R3-S5, 18.1R3-S6, 18.1R3-S7, 18.1R3-S8; 18.2R3, 18.2R3-S1, 18.2R3-S2; 18.3R2 and the SRs based on 18.3R2; 18.4R2 and the SRs based on 18.4R2; 19.1R1 and the SRs based on 19.1R1; 19.2R1 and the SRs based on 19.2R1; 19.3R1 and the SRs based on 19.3R1.

Show More

When a device running Juniper Networks Junos OS with MPC7, MPC8, or MPC9 line cards installed and the system is configured for inline IP reassembly, used by L2TP, MAP-E, GRE, and IPIP, the packet forwarding engine (PFE) will become disabled upon receipt of small fragments requiring reassembly, generating the following error messages: [LOG: Err] MQSS(2): WO: Packet Error - Error Packets 1, Connection 29 [LOG: Err] eachip_hmcif_rx_intr_handler(7259): EA[2:0]: HMCIF Rx: Injected checksum error dete ... When a device running Juniper Networks Junos OS with MPC7, MPC8, or MPC9 line cards installed and the system is configured for inline IP reassembly, used by L2TP, MAP-E, GRE, and IPIP, the packet forwarding engine (PFE) will become disabled upon receipt of small fragments requiring reassembly, generating the following error messages: [LOG: Err] MQSS(2): WO: Packet Error - Error Packets 1, Connection 29 [LOG: Err] eachip_hmcif_rx_intr_handler(7259): EA[2:0]: HMCIF Rx: Injected checksum error detected on WO response - Chunk Address 0x0 [LOG: Err] MQSS(2): DRD: RORD1: CMD reorder ID error - Command 11, Reorder ID 1960, QID 0 [LOG: Err] MQSS(2): DRD: UNROLL0: HMC chunk address error in stage 5 - Chunk Address: 0xc38fb1 [LOG: Notice] Error: /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc), scope: pfe, category: functional, severity: major, module: MQSS(2), type: DRD_RORD_ENG_INT: CMD FSM State Error [LOG: Notice] Performing action cmalarm for error /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(2) with scope: pfe category: functional level: major [LOG: Notice] Performing action get-state for error /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(2) with scope: pfe category: functional level: major [LOG: Notice] Performing action disable-pfe for error /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(2) with scope: pfe category: functional level: major By continuously sending fragmented packets that cannot be reassembled, an attacker can repeatedly disable the PFE causing a sustained Denial of Service (DoS). This issue affects Juniper Networks Junos OS: 17.2 versions prior to 17.2R3-S4 on MX Series; 17.3 versions prior to 17.3R3-S8 on MX Series; 17.4 versions prior to 17.4R2-S9, 17.4R3-S1 on MX Series; 18.1 versions prior to 18.1R3-S10 on MX Series; 18.2 versions prior to 18.2R2-S6, 18.2R3-S3 on MX Series; 18.2X75 versions prior to 18.2X75-D34, 18.2X75-D41, 18.2X75-D53, 18.2X75-D65, 18.2X75-D430 on MX Series; 18.3 versions prior to 18.3R1-S7, 18.3R2-S4, 18.3R3-S2 on MX Series; 18.4 versions prior to 18.4R1-S6, 18.4R2-S4, 18.4R3 on MX Series; 19.1 versions prior to 19.1R1-S4, 19.1R2-S1, 19.1R3 on MX Series; 19.2 versions prior to 19.2R1-S3, 19.2R2 on MX Series; 19.3 versions prior to 19.3R2-S2, 19.3R3 on MX Series. This issue is specific to inline IP reassembly, introduced in Junos OS 17.2. Versions of Junos OS prior to 17.2 are unaffected by this vulnerability.

Show More

On Juniper Networks Junos OS and Junos OS Evolved devices, processing a specific BGP packet can lead to a routing process daemon (RPD) crash and restart. This issue can occur even before the BGP session with the peer is established. Repeated receipt of this specific BGP packet can result in an extended Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS: 18.2X75 versions starting from 18.2X75-D50.8, 18.2X75-D60 and later versions, prior to 18.2X75-D52.8, 18.2X75-D53, ... On Juniper Networks Junos OS and Junos OS Evolved devices, processing a specific BGP packet can lead to a routing process daemon (RPD) crash and restart. This issue can occur even before the BGP session with the peer is established. Repeated receipt of this specific BGP packet can result in an extended Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS: 18.2X75 versions starting from 18.2X75-D50.8, 18.2X75-D60 and later versions, prior to 18.2X75-D52.8, 18.2X75-D53, 18.2X75-D60.2, 18.2X75-D65.1, 18.2X75-D70; 19.4 versions 19.4R1 and 19.4R1-S1; 20.1 versions prior to 20.1R1-S2, 20.1R2. Juniper Networks Junos OS Evolved: 19.4-EVO versions prior to 19.4R2-S2-EVO; 20.1-EVO versions prior to 20.1R2-EVO. This issue does not affect: Juniper Networks Junos OS releases prior to 19.4R1. Juniper Networks Junos OS Evolved releases prior to 19.4R1-EVO.

Show More

On Juniper Networks SRX Series with ICAP (Internet Content Adaptation Protocol) redirect service enabled, a double free vulnerability can lead to a Denial of Service (DoS) or Remote Code Execution (RCE) due to processing of a specific HTTP message. Continued processing of this specific HTTP message may result in an extended Denial of Service (DoS). The offending HTTP message that causes this issue may originate both from the HTTP server or the client. This issue affects Juniper Networks Junos OS ... On Juniper Networks SRX Series with ICAP (Internet Content Adaptation Protocol) redirect service enabled, a double free vulnerability can lead to a Denial of Service (DoS) or Remote Code Execution (RCE) due to processing of a specific HTTP message. Continued processing of this specific HTTP message may result in an extended Denial of Service (DoS). The offending HTTP message that causes this issue may originate both from the HTTP server or the client. This issue affects Juniper Networks Junos OS on SRX Series: 18.1 versions prior to 18.1R3-S9; 18.2 versions prior to 18.2R3-S3; 18.3 versions prior to 18.3R2-S4, 18.3R3-S1; 18.4 versions prior to 18.4R2-S5, 18.4R3; 19.1 versions prior to 19.1R2; 19.2 versions prior to 19.2R1-S2, 19.2R2; 19.3 versions prior to 19.3R2. This issue does not affect Juniper Networks Junos OS prior to 18.1R1.

Show More

On Juniper Networks Junos OS and Junos OS Evolved devices, processing a specific UPDATE for an EBGP peer can lead to a routing process daemon (RPD) crash and restart. This issue occurs only when the device is receiving and processing the BGP UPDATE for an EBGP peer. This issue does not occur when the device is receiving and processing the BGP UPDATE for an IBGP peer. However, the offending BGP UPDATE can originally come from an EBGP peer, propagates through the network via IBGP peers without cau ... On Juniper Networks Junos OS and Junos OS Evolved devices, processing a specific UPDATE for an EBGP peer can lead to a routing process daemon (RPD) crash and restart. This issue occurs only when the device is receiving and processing the BGP UPDATE for an EBGP peer. This issue does not occur when the device is receiving and processing the BGP UPDATE for an IBGP peer. However, the offending BGP UPDATE can originally come from an EBGP peer, propagates through the network via IBGP peers without causing crash, then it causes RPD crash when it is processed for a BGP UPDATE towards an EBGP peer. Repeated receipt and processing of the same specific BGP UPDATE can result in an extended Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS: 17.3R3-S6, 17.4R2-S7, and 18.1R3-S7. Juniper Networks Junos OS Evolved 19.2R2-EVO and later versions, prior to 19.3R1-EVO. Other Junos OS releases are not affected.

Show More

When DNS filtering is enabled on Juniper Networks Junos MX Series with one of the following cards MS-PIC, MS-MIC or MS-MPC, an incoming stream of packets processed by the Multiservices PIC Management Daemon (mspmand) process, responsible for managing "URL Filtering service", may crash, causing the Services PIC to restart. While the Services PIC is restarting, all PIC services including DNS filtering service (DNS sink holing) will be bypassed until the Services PIC completes its boot process. If ... When DNS filtering is enabled on Juniper Networks Junos MX Series with one of the following cards MS-PIC, MS-MIC or MS-MPC, an incoming stream of packets processed by the Multiservices PIC Management Daemon (mspmand) process, responsible for managing "URL Filtering service", may crash, causing the Services PIC to restart. While the Services PIC is restarting, all PIC services including DNS filtering service (DNS sink holing) will be bypassed until the Services PIC completes its boot process. If the issue occurs, system core-dumps output will show a crash of mspmand process: root@device> show system core-dumps -rw-rw---- 1 nobody wheel 575685123 <Date> /var/tmp/pics/mspmand.core.<*>.gz This issue affects Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S8; 18.3 versions prior to 18.3R2-S4, 18.3R3-S1; 18.4 versions prior to 18.4R2-S5, 18.4R3; 19.1 versions prior to 19.1R2-S2, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2. This issue does not affect Juniper Networks Junos OS releases prior to 17.3R2.

Show More

On Juniper Networks Junos OS and Junos OS Evolved devices, the receipt of a specific BGP UPDATE packet causes an internal counter to be incremented incorrectly, which over time can lead to the routing protocols process (RPD) crash and restart. This issue affects both IBGP and EBGP multihop deployment in IPv4 or IPv6 network. This issue affects: Juniper Networks Junos OS: 17.2X75 versions prior to 17.2X75-D105.19; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S10, 17.4R3-S2; 18. ... On Juniper Networks Junos OS and Junos OS Evolved devices, the receipt of a specific BGP UPDATE packet causes an internal counter to be incremented incorrectly, which over time can lead to the routing protocols process (RPD) crash and restart. This issue affects both IBGP and EBGP multihop deployment in IPv4 or IPv6 network. This issue affects: Juniper Networks Junos OS: 17.2X75 versions prior to 17.2X75-D105.19; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S10, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R2-S7, 18.2R3-S4; 18.2X75 versions prior to 18.2X75-D13, 18.2X75-D411.1, 18.2X75-D420.18, 18.2X75-D52.3, 18.2X75-D60; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3-S2; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S2, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2. Juniper Networks Junos OS Evolved: any releases prior to 20.1R2-EVO. This issue does not affect Juniper Networks Junos OS releases prior to 17.3R1.

Show More

Execution of the "show ospf interface extensive" or "show ospf interface detail" CLI commands on a Juniper Networks device running Junos OS may cause the routing protocols process (RPD) to crash and restart if OSPF interface authentication is configured, leading to a Denial of Service (DoS). By continuously executing the same CLI commands, a local attacker can repeatedly crash the RPD process causing a sustained Denial of Service. Note: Only systems utilizing ARM processors, found on the EX2300 ... Execution of the "show ospf interface extensive" or "show ospf interface detail" CLI commands on a Juniper Networks device running Junos OS may cause the routing protocols process (RPD) to crash and restart if OSPF interface authentication is configured, leading to a Denial of Service (DoS). By continuously executing the same CLI commands, a local attacker can repeatedly crash the RPD process causing a sustained Denial of Service. Note: Only systems utilizing ARM processors, found on the EX2300 and EX3400, are vulnerable to this issue. Systems shipped with other processor architectures are not vulnerable to this issue. The processor architecture can be displayed via the 'uname -a' command. For example: ARM (vulnerable): % uname -a | awk '{print $NF}' arm PowerPC (not vulnerable): % uname -a | awk '{print $NF}' powerpc AMD (not vulnerable): % uname -a | awk '{print $NF}' amd64 Intel (not vulnerable): % uname -a | awk '{print $NF}' i386 This issue affects Juniper Networks Junos OS: 12.3X48 versions prior to 12.3X48-D100; 14.1X53 versions prior to 14.1X53-D140, 14.1X53-D54; 15.1 versions prior to 15.1R7-S7; 15.1X49 versions prior to 15.1X49-D210; 15.1X53 versions prior to 15.1X53-D593; 16.1 versions prior to 16.1R7-S8; 17.1 versions prior to 17.1R2-S12; 17.2 versions prior to 17.2R3-S4; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S2, 17.4R3; 18.1 versions prior to 18.1R3-S2; 18.2 versions prior to 18.2R2, 18.2R3; 18.2X75 versions prior to 18.2X75-D40; 18.3 versions prior to 18.3R1-S2, 18.3R2.

Show More

A Race Condition vulnerability in Juniper Networks Junos OS LLDP implementation allows an attacker to cause LLDP to crash leading to a Denial of Service (DoS). This issue occurs when crafted LLDP packets are received by the device from an adjacent device. Multiple LACP flaps will occur after LLDP crashes. An indicator of compromise is to evaluate log file details for lldp with RLIMIT. Intervention should occur before 85% threshold of used KB versus maximum available KB memory is reached. show lo ... A Race Condition vulnerability in Juniper Networks Junos OS LLDP implementation allows an attacker to cause LLDP to crash leading to a Denial of Service (DoS). This issue occurs when crafted LLDP packets are received by the device from an adjacent device. Multiple LACP flaps will occur after LLDP crashes. An indicator of compromise is to evaluate log file details for lldp with RLIMIT. Intervention should occur before 85% threshold of used KB versus maximum available KB memory is reached. show log messages | match RLIMIT | match lldp | last 20 Matching statement is " /kernel: %KERNEL-[number]: Process ([pid #],lldpd) has exceeded 85% of RLIMIT_DATA: " with [] as variable data to evaluate for. This issue affects: Juniper Networks Junos OS: 12.3 versions prior to 12.3R12-S15; 12.3X48 versions prior to 12.3X48-D95; 15.1 versions prior to 15.1R7-S6; 15.1X49 versions prior to 15.1X49-D200; 15.1X53 versions prior to 15.1X53-D593; 16.1 versions prior to 16.1R7-S7; 17.1 versions prior to 17.1R2-S11, 17.1R3-S2; 17.2 versions prior to 17.2R1-S9, 17.2R3-S3; 17.3 versions prior to 17.3R2-S5, 17.3R3-S6; 17.4 versions prior to 17.4R2-S4, 17.4R3; 18.1 versions prior to 18.1R3-S5; 18.2 versions prior to 18.2R2-S7, 18.2R3; 18.2X75 versions prior to 18.2X75-D12, 18.2X75-D33, 18.2X75-D50, 18.2X75-D420; 18.3 versions prior to 18.3R1-S7, 18.3R2-S3, 18.3R3; 18.4 versions prior to 18.4R1-S5, 18.4R2; 19.1 versions prior to 19.1R1-S4, 19.1R2.

Show More

An improper use of a validation framework when processing incoming genuine BGP packets within Juniper Networks RPD (routing protocols process) daemon allows an attacker to crash RPD thereby causing a Denial of Service (DoS) condition. This framework requires these packets to be passed. By continuously sending any of these types of formatted genuine packets, an attacker can repeatedly crash the RPD process causing a sustained Denial of Service. Authentication to the BGP peer is not required. This ... An improper use of a validation framework when processing incoming genuine BGP packets within Juniper Networks RPD (routing protocols process) daemon allows an attacker to crash RPD thereby causing a Denial of Service (DoS) condition. This framework requires these packets to be passed. By continuously sending any of these types of formatted genuine packets, an attacker can repeatedly crash the RPD process causing a sustained Denial of Service. Authentication to the BGP peer is not required. This issue can be initiated or propagated through eBGP and iBGP and can impact devices in either modes of use as long as the devices are configured to support the compromised framework and a BGP path is activated or active. This issue affects: Juniper Networks Junos OS 16.1 versions 16.1R7-S6 and later versions prior to 16.1R7-S8; 17.3 versions 17.3R2-S5, 17.3R3-S6 and later versions prior to 17.3R3-S8; 17.4 versions 17.4R2-S7, 17.4R3 and later versions prior to 17.4R2-S11, 17.4R3-S2; 18.1 versions 18.1R3-S7 and later versions prior to 18.1R3-S10; 18.2 versions 18.2R2-S6, 18.2R3-S2 and later versions prior to 18.2R2-S7, 18.2R3-S5; 18.2X75 versions 18.2X75-D12, 18.2X75-D32, 18.2X75-D33, 18.2X75-D51, 18.2X75-D60, 18.2X75-D411, 18.2X75-D420 and later versions prior to 18.2X75-D32, 18.2X75-D33, 18.2X75-D420, 18.2X75-D52, 18.2X75-D60, 18.2X75-D65, 18.2X75-D70;(*1) 18.3 versions 18.3R1-S6, 18.3R2-S3, 18.3R3 and later versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions 18.4R1-S5, 18.4R2-S4, 18.4R3 and later versions prior to 18.4R1-S7, 18.4R2-S5, 18.4R3-S3(*2); 19.1 versions 19.1R1-S3, 19.1R2 and later versions prior to 19.1R1-S5, 19.1R2-S2, 19.1R3-S2; 19.2 versions 19.2R1-S2, 19.2R2 and later versions prior to 19.2R1-S5, 19.2R2, 19.2R3; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2, 19.4R3; 20.1 versions prior to 20.1R1-S1, 20.1R2. This issue does not affect Junos OS prior to 16.1R1. This issue affects IPv4 and IPv6 traffic.

Show More

When an attacker sends a specific crafted Ethernet Operation, Administration, and Maintenance (Ethernet OAM) packet to a target device, it may improperly handle the incoming malformed data and fail to sanitize this incoming data resulting in an overflow condition. This overflow condition in Juniper Networks Junos OS allows an attacker to cause a Denial of Service (DoS) condition by coring the CFM daemon. Continued receipt of these packets may cause an extended Denial of Service condition. This i ... When an attacker sends a specific crafted Ethernet Operation, Administration, and Maintenance (Ethernet OAM) packet to a target device, it may improperly handle the incoming malformed data and fail to sanitize this incoming data resulting in an overflow condition. This overflow condition in Juniper Networks Junos OS allows an attacker to cause a Denial of Service (DoS) condition by coring the CFM daemon. Continued receipt of these packets may cause an extended Denial of Service condition. This issue affects: Juniper Networks Junos OS 12.3 versions prior to 12.3R12-S15; 12.3X48 versions prior to 12.3X48-D95 on SRX Series; 14.1X50 versions prior to 14.1X50-D145; 14.1X53 versions prior to 14.1X53-D47; 15.1 versions prior to 15.1R2; 15.1X49 versions prior to 15.1X49-D170 on SRX Series; 15.1X53 versions prior to 15.1X53-D67.

Show More

The FPC (Flexible PIC Concentrator) of Juniper Networks Junos OS and Junos OS Evolved may restart after processing a specific IPv4 packet. Only packets destined to the device itself, successfully reaching the RE through existing edge and control plane filtering, will be able to cause the FPC restart. When this issue occurs, all traffic via the FPC will be dropped. By continuously sending this specific IPv4 packet, an attacker can repeatedly crash the FPC, causing an extended Denial of Service (D ... The FPC (Flexible PIC Concentrator) of Juniper Networks Junos OS and Junos OS Evolved may restart after processing a specific IPv4 packet. Only packets destined to the device itself, successfully reaching the RE through existing edge and control plane filtering, will be able to cause the FPC restart. When this issue occurs, all traffic via the FPC will be dropped. By continuously sending this specific IPv4 packet, an attacker can repeatedly crash the FPC, causing an extended Denial of Service (DoS) condition. This issue can only occur when processing a specific IPv4 packet. IPv6 packets cannot trigger this issue. This issue affects: Juniper Networks Junos OS on MX Series with MPC10E or MPC11E and PTX10001: 19.2 versions prior to 19.2R1-S4, 19.2R2; 19.3 versions prior to 19.3R2-S2, 19.3R3; 19.4 versions prior to 19.4R1-S1, 19.4R2. Juniper Networks Junos OS Evolved on on QFX5220, and PTX10003 series: 19.2-EVO versions; 19.3-EVO versions; 19.4-EVO versions prior to 19.4R2-EVO. This issue does not affect Junos OS versions prior to 19.2R1. This issue does not affect Junos OS Evolved versions prior to 19.2R1-EVO.

Show More

A vulnerability in Juniper Networks SRX Series device configured as a Junos OS Enforcer device may allow a user to access network resources that are not permitted by a UAC policy. This issue might occur when the IP address range configured in the Infranet Controller (IC) is configured as an IP address range instead of an IP address/netmask. See the Workaround section for more detail. The Junos OS Enforcer CLI settings are disabled by default. This issue affects Juniper Networks Junos OS on SRX S ... A vulnerability in Juniper Networks SRX Series device configured as a Junos OS Enforcer device may allow a user to access network resources that are not permitted by a UAC policy. This issue might occur when the IP address range configured in the Infranet Controller (IC) is configured as an IP address range instead of an IP address/netmask. See the Workaround section for more detail. The Junos OS Enforcer CLI settings are disabled by default. This issue affects Juniper Networks Junos OS on SRX Series: 12.3X48 versions prior to 12.3X48-D100; 15.1X49 versions prior to 15.1X49-D210; 17.3 versions prior to 17.3R2-S5, 17.3R3-S8; 17.4 versions prior to 17.4R2-S9, 17.4R3-S1; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R2-S7, 18.2R3-S3; 18.3 versions prior to 18.3R1-S7, 18.3R3-S2; 18.4 versions prior to 18.4R1-S6, 18.4R2-S4, 18.4R3-S1; 19.1 versions prior to 19.1R1-S4, 19.1R2-S1, 19.1R3; 19.2 versions prior to 19.2R1-S3, 19.2R2; 19.3 versions prior to 19.3R2-S1, 19.3R3; 19.4 versions prior to 19.4R1-S1, 19.4R2.

Show More

On High-End SRX Series devices, in specific configurations and when specific networking events or operator actions occur, an SPC receiving genuine multicast traffic may core. Subsequently, all FPCs in a chassis may reset causing a Denial of Service. This issue affects both IPv4 and IPv6. This issue affects: Juniper Networks Junos OS 12.3X48 version 12.3X48-D80 and later versions prior to 12.3X48-D95 on High-End SRX Series. This issue does not affect Branch SRX Series devices.

Due to a new NDP proxy feature for EVPN leaf nodes introduced in Junos OS 17.4, crafted NDPv6 packets could transit a Junos device configured as a Broadband Network Gateway (BNG) and reach the EVPN leaf node, causing a stale MAC address entry. This could cause legitimate traffic to be discarded, leading to a Denial of Service (DoS) condition. This issue only affects Junos OS 17.4 and later releases. Prior releases do not support this feature and are unaffected by this vulnerability. This issue o ... Due to a new NDP proxy feature for EVPN leaf nodes introduced in Junos OS 17.4, crafted NDPv6 packets could transit a Junos device configured as a Broadband Network Gateway (BNG) and reach the EVPN leaf node, causing a stale MAC address entry. This could cause legitimate traffic to be discarded, leading to a Denial of Service (DoS) condition. This issue only affects Junos OS 17.4 and later releases. Prior releases do not support this feature and are unaffected by this vulnerability. This issue only affects IPv6. IPv4 ARP proxy is unaffected by this vulnerability. This issue affects Juniper Networks Junos OS: 17.4 versions prior to 17.4R2-S9, 17.4R3 on MX Series; 18.1 versions prior to 18.1R3-S9 on MX Series; 18.2 versions prior to 18.2R2-S7, 18.2R3-S3 on MX Series; 18.2X75 versions prior to 18.2X75-D33, 18.2X75-D411, 18.2X75-D420, 18.2X75-D60 on MX Series; 18.3 versions prior to 18.3R1-S7, 18.3R2-S3, 18.3R3 on MX Series; 18.4 versions prior to 18.4R1-S5, 18.4R2-S2, 18.4R3 on MX Series; 19.1 versions prior to 19.1R1-S4, 19.1R2 on MX Series; 19.2 versions prior to 19.2R1-S3, 19.2R2 on MX Series.

Show More

In a certain condition, receipt of a specific BGP UPDATE message might cause Juniper Networks Junos OS and Junos OS Evolved devices to advertise an invalid BGP UPDATE message to other peers, causing the other peers to terminate the established BGP session, creating a Denial of Service (DoS) condition. For example, Router A sends a specific BGP UPDATE to Router B, causing Router B to send an invalid BGP UPDATE message to Router C, resulting in termination of the BGP session between Router B and R ... In a certain condition, receipt of a specific BGP UPDATE message might cause Juniper Networks Junos OS and Junos OS Evolved devices to advertise an invalid BGP UPDATE message to other peers, causing the other peers to terminate the established BGP session, creating a Denial of Service (DoS) condition. For example, Router A sends a specific BGP UPDATE to Router B, causing Router B to send an invalid BGP UPDATE message to Router C, resulting in termination of the BGP session between Router B and Router C. This issue might occur when there is at least a single BGP session established on the device that does not support 4 Byte AS extension (RFC 4893). Repeated receipt of the same BGP UPDATE can result in an extended DoS condition. This issue affects Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S6; 16.2 versions prior to 16.2R2-S11; 17.1 versions prior to 17.1R2-S11, 17.1R3-S2; 17.2 versions prior to 17.2R1-S9, 17.2R2-S8, 17.2R3-S3; 17.2X75 versions prior to 17.2X75-D105, 17.2X75-D110, 17.2X75-D44; 17.3 versions prior to 17.3R2-S5, 17.3R3-S7; 17.4 versions prior to 17.4R2-S8, 17.4R3; 18.1 versions prior to 18.1R3-S8; 18.2 versions prior to 18.2R2-S6, 18.2R3-S2; 18.2X75 versions prior to 18.2X75-D12, 18.2X75-D33, 18.2X75-D411, 18.2X75-D420, 18.2X75-D51, 18.2X75-D60; 18.3 versions prior to 18.3R1-S6, 18.3R2-S3, 18.3R3; 18.4 versions prior to 18.4R1-S5, 18.4R3; 18.4 version 18.4R2 and later versions; 19.1 versions prior to 19.1R1-S3, 19.1R2; 19.2 versions prior to 19.2R1-S2, 19.2R2. This issue does not affect Juniper Networks Junos OS prior to 16.1R1. This issue affects Juniper Networks Junos OS Evolved prior to 19.2R2-EVO.

Show More

A privilege escalation vulnerability in Juniper Networks Junos OS devices configured with dual Routing Engines (RE), Virtual Chassis (VC) or high-availability cluster may allow a local authenticated low-privileged user with access to the shell to perform unauthorized configuration modification. This issue does not affect Junos OS device with single RE or stand-alone configuration. This issue affects Juniper Networks Junos OS 12.3 versions prior to 12.3R12-S14; 12.3X48 versions prior to 12.3X48-D ... A privilege escalation vulnerability in Juniper Networks Junos OS devices configured with dual Routing Engines (RE), Virtual Chassis (VC) or high-availability cluster may allow a local authenticated low-privileged user with access to the shell to perform unauthorized configuration modification. This issue does not affect Junos OS device with single RE or stand-alone configuration. This issue affects Juniper Networks Junos OS 12.3 versions prior to 12.3R12-S14; 12.3X48 versions prior to 12.3X48-D86, 12.3X48-D90; 14.1X53 versions prior to 14.1X53-D51; 15.1 versions prior to 15.1R7-S6; 15.1X49 versions prior to 15.1X49-D181, 15.1X49-D190; 15.1X53 versions prior to 15.1X53-D592; 16.1 versions prior to 16.1R4-S13, 16.1R7-S6; 16.2 versions prior to 16.2R2-S10; 17.1 versions prior to 17.1R2-S11, 17.1R3-S1; 17.2 versions prior to 17.2R1-S9, 17.2R3-S3; 17.3 versions prior to 17.3R3-S6; 17.4 versions prior to 17.4R2-S6, 17.4R3; 18.1 versions prior to 18.1R3-S7; 18.2 versions prior to 18.2R2-S5, 18.2R3-S1; 18.2 versions prior to 18.2X75-D12, 18.2X75-D33, 18.2X75-D420, 18.2X75-D60, 18.2X75-D411; 18.3 versions prior to 18.3R1-S5, 18.3R2-S1, 18.3R3; 18.4 versions prior to 18.4R1-S4, 18.4R2-S1, 18.4R3; 19.1 versions prior to 19.1R1-S2, 19.1R2; 19.2 versions prior to 19.2R1-S1, 19.2R2.

Show More

A race condition vulnerability on Juniper Network Junos OS devices may cause the routing protocol daemon (RPD) process to crash and restart while processing a BGP NOTIFICATION message. This issue affects Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S6; 16.2 versions prior to 16.2R2-S11; 17.1 versions prior to 17.1R2-S11, 17.1R3-S1; 17.2 versions prior to 17.2R1-S9, 17.2R3-S3; 17.2 version 17.2R2 and later versions; 17.2X75 versions prior to 17.2X75-D105, 17.2X75-D110; 17.3 versions p ... A race condition vulnerability on Juniper Network Junos OS devices may cause the routing protocol daemon (RPD) process to crash and restart while processing a BGP NOTIFICATION message. This issue affects Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S6; 16.2 versions prior to 16.2R2-S11; 17.1 versions prior to 17.1R2-S11, 17.1R3-S1; 17.2 versions prior to 17.2R1-S9, 17.2R3-S3; 17.2 version 17.2R2 and later versions; 17.2X75 versions prior to 17.2X75-D105, 17.2X75-D110; 17.3 versions prior to 17.3R2-S5, 17.3R3-S6; 17.4 versions prior to 17.4R2-S7, 17.4R3; 18.1 versions prior to 18.1R3-S8; 18.2 versions prior to 18.2R3-S3; 18.2X75 versions prior to 18.2X75-D410, 18.2X75-D420, 18.2X75-D50, 18.2X75-D60; 18.3 versions prior to 18.3R1-S5, 18.3R2-S2, 18.3R3; 18.4 versions prior to 18.4R2-S2, 18.4R3; 19.1 versions prior to 19.1R1-S2, 19.1R2; 19.2 versions prior to 19.2R1-S4, 19.2R2. This issue does not affect Juniper Networks Junos OS prior to version 16.1R1.

Show More

Juniper Networks Junos OS uses the 128.0.0.0/2 subnet for internal communications between the RE and PFEs. It was discovered that packets utilizing these IP addresses may egress an EX4300 switch, leaking configuration information such as heartbeats, kernel versions, etc. out to the Internet, leading to an information exposure vulnerability. This issue affects Juniper Networks Junos OS: 14.1X53 versions prior to 14.1X53-D53 on EX4300; 15.1 versions prior to 15.1R7-S6 on EX4300; 15.1X49 versions p ... Juniper Networks Junos OS uses the 128.0.0.0/2 subnet for internal communications between the RE and PFEs. It was discovered that packets utilizing these IP addresses may egress an EX4300 switch, leaking configuration information such as heartbeats, kernel versions, etc. out to the Internet, leading to an information exposure vulnerability. This issue affects Juniper Networks Junos OS: 14.1X53 versions prior to 14.1X53-D53 on EX4300; 15.1 versions prior to 15.1R7-S6 on EX4300; 15.1X49 versions prior to 15.1X49-D200, 15.1X49-D210 on EX4300; 16.1 versions prior to 16.1R7-S7 on EX4300; 17.1 versions prior to 17.1R2-S11, 17.1R3-S2 on EX4300; 17.2 versions prior to 17.2R3-S3 on EX4300; 17.3 versions prior to 17.3R2-S5, 17.3R3-S7 on EX4300; 17.4 versions prior to 17.4R2-S9, 17.4R3 on EX4300; 18.1 versions prior to 18.1R3-S8 on EX4300; 18.2 versions prior to 18.2R3-S2 on EX4300; 18.3 versions prior to 18.3R2-S3, 18.3R3, 18.3R3-S1 on EX4300; 18.4 versions prior to 18.4R1-S5, 18.4R2-S3, 18.4R3 on EX4300; 19.1 versions prior to 19.1R1-S4, 19.1R2 on EX4300; 19.2 versions prior to 19.2R1-S4, 19.2R2 on EX4300; 19.3 versions prior to 19.3R1-S1, 19.3R2 on EX4300.

Show More

A vulnerability in Juniper Networks Junos OS on vMX and MX150 devices may allow an attacker to cause a Denial of Service (DoS) by sending specific packets requiring special processing in microcode that the flow cache can't handle, causing the riot forwarding daemon to crash. By continuously sending the same specific packets, an attacker can repeatedly crash the riot process causing a sustained Denial of Service. Flow cache is specific to vMX based products and the MX150, and is enabled by defaul ... A vulnerability in Juniper Networks Junos OS on vMX and MX150 devices may allow an attacker to cause a Denial of Service (DoS) by sending specific packets requiring special processing in microcode that the flow cache can't handle, causing the riot forwarding daemon to crash. By continuously sending the same specific packets, an attacker can repeatedly crash the riot process causing a sustained Denial of Service. Flow cache is specific to vMX based products and the MX150, and is enabled by default in performance mode. This issue can only be triggered by traffic destined to the device. Transit traffic will not cause the riot daemon to crash. When the issue occurs, a core dump and riot log file entry are generated. For example: /var/crash/core.J-UKERN.mpc0.1557255993.3864.gz /home/pfe/RIOT logs: fpc0 riot[1888]: PANIC in lu_reorder_send_packet_postproc(): fpc0 riot[6655]: PANIC in lu_reorder_send_packet_postproc(): This issue affects Juniper Networks Junos OS: 18.1 versions prior to 18.1R3 on vMX and MX150; 18.2 versions prior to 18.2R3 on vMX and MX150; 18.2X75 versions prior to 18.2X75-D60 on vMX and MX150; 18.3 versions prior to 18.3R3 on vMX and MX150; 18.4 versions prior to 18.4R2 on vMX and MX150; 19.1 versions prior to 19.1R2 on vMX and MX150. This issue does not affect Junos OS versions prior to 18.1R1.

Show More

The kernel memory usage represented as "temp" via 'show system virtual-memory' may constantly increase when Integrated Routing and Bridging (IRB) is configured with multiple underlay physical interfaces, and one interface flaps. This memory leak can affect running daemons (processes), leading to an extended Denial of Service (DoS) condition. Usage of "temp" virtual memory, shown here by a constantly increasing value of outstanding Requests, can be monitored by executing the 'show system virtual- ... The kernel memory usage represented as "temp" via 'show system virtual-memory' may constantly increase when Integrated Routing and Bridging (IRB) is configured with multiple underlay physical interfaces, and one interface flaps. This memory leak can affect running daemons (processes), leading to an extended Denial of Service (DoS) condition. Usage of "temp" virtual memory, shown here by a constantly increasing value of outstanding Requests, can be monitored by executing the 'show system virtual-memory' command as shown below: user@junos> show system virtual-memory |match "fpc|type|temp" fpc0: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2023 431K - 10551 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 fpc1: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2020 431K - 6460 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 user@junos> show system virtual-memory |match "fpc|type|temp" fpc0: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2023 431K - 16101 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 fpc1: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2020 431K - 6665 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 user@junos> show system virtual-memory |match "fpc|type|temp" fpc0: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2023 431K - 21867 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 fpc1: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2020 431K - 6858 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 This issue affects Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S6; 17.1 versions prior to 17.1R2-S11, 17.1R3-S1; 17.2 versions prior to 17.2R2-S8, 17.2R3-S3; 17.2X75 versions prior to 17.2X75-D44; 17.3 versions prior to 17.3R2-S5, 17.3R3-S6; 17.4 versions prior to 17.4R2-S5, 17.4R3; 18.1 versions prior to 18.1R3-S7; 18.2 versions prior to 18.2R2-S5, 18.2R3; 18.2X75 versions prior to 18.2X75-D33, 18.2X75-D411, 18.2X75-D420, 18.2X75-D60; 18.3 versions prior to 18.3R1-S5, 18.3R2-S3, 18.3R3; 18.4 versions prior to 18.4R2-S2, 18.4R3; 19.1 versions prior to 19.1R1-S3, 19.1R2; 19.2 versions prior to 19.2R1-S3, 19.2R2. This issue does not affect Juniper Networks Junos OS 12.3 and 15.1.

Show More

A privilege escalation vulnerability in Juniper Networks QFX10K Series, EX9200 Series, MX Series, and PTX Series with Next-Generation Routing Engine (NG-RE), allows a local authenticated high privileged user to access the underlying WRL host. This issue only affects QFX10K Series with NG-RE, EX9200 Series with NG-RE, MX Series with NG-RE and PTX Series with NG-RE; which uses vmhost. This issue affects Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S6; 16.2 versions prior to 16.2R2-S11; ... A privilege escalation vulnerability in Juniper Networks QFX10K Series, EX9200 Series, MX Series, and PTX Series with Next-Generation Routing Engine (NG-RE), allows a local authenticated high privileged user to access the underlying WRL host. This issue only affects QFX10K Series with NG-RE, EX9200 Series with NG-RE, MX Series with NG-RE and PTX Series with NG-RE; which uses vmhost. This issue affects Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S6; 16.2 versions prior to 16.2R2-S11; 17.1 versions prior to 17.1R2-S11, 17.1R3; 17.2 versions prior to 17.2R1-S9, 17.2R3-S3; 17.3 versions prior to 17.3R2-S5, 17.3R3-S7; 17.4 versions prior to 17.4R2-S7, 17.4R3; 18.1 versions prior to 18.1R3-S4; 18.2 versions prior to 18.2R3; 18.2X75 versions prior to 18.2X75-D50; 18.3 versions prior to 18.3R2; 18.4 versions prior to 18.4R2. To identify whether the device has NG-RE with vmhost, customer can run the following command: > show vmhost status Compute cluster: rainier-re-cc Compute Node: rainier-re-cn, Online If the "show vmhost status" is not supported, then the device does not have NG-RE with vmhost.

Show More

On Juniper Networks EX and QFX Series, an authentication bypass vulnerability may allow a user connected to the console port to login as root without any password. This issue might only occur in certain scenarios: • At the first reboot after performing device factory reset using the command “request system zeroize”; or • A temporary moment during the first reboot after the software upgrade when the device configured in Virtual Chassis mode. This issue affects Juniper Networks Junos OS on EX and ... On Juniper Networks EX and QFX Series, an authentication bypass vulnerability may allow a user connected to the console port to login as root without any password. This issue might only occur in certain scenarios: • At the first reboot after performing device factory reset using the command “request system zeroize”; or • A temporary moment during the first reboot after the software upgrade when the device configured in Virtual Chassis mode. This issue affects Juniper Networks Junos OS on EX and QFX Series: 14.1X53 versions prior to 14.1X53-D53; 15.1 versions prior to 15.1R7-S4; 15.1X53 versions prior to 15.1X53-D593; 16.1 versions prior to 16.1R7-S4; 17.1 versions prior to 17.1R2-S11, 17.1R3-S1; 17.2 versions prior to 17.2R3-S3; 17.3 versions prior to 17.3R2-S5, 17.3R3-S6; 17.4 versions prior to 17.4R2-S9, 17.4R3; 18.1 versions prior to 18.1R3-S8; 18.2 versions prior to 18.2R2; 18.3 versions prior to 18.3R1-S7, 18.3R2. This issue does not affect Juniper Networks Junos OS 12.3.

Show More

This issue occurs on Juniper Networks Junos OS devices which do not support Advanced Forwarding Interface (AFI) / Advanced Forwarding Toolkit (AFT). Devices using AFI and AFT are not exploitable to this issue. An improper initialization of memory in the packet forwarding architecture in Juniper Networks Junos OS non-AFI/AFT platforms which may lead to a Denial of Service (DoS) vulnerability being exploited when a genuine packet is received and inspected by non-AFT/AFI sFlow and when the device i ... This issue occurs on Juniper Networks Junos OS devices which do not support Advanced Forwarding Interface (AFI) / Advanced Forwarding Toolkit (AFT). Devices using AFI and AFT are not exploitable to this issue. An improper initialization of memory in the packet forwarding architecture in Juniper Networks Junos OS non-AFI/AFT platforms which may lead to a Denial of Service (DoS) vulnerability being exploited when a genuine packet is received and inspected by non-AFT/AFI sFlow and when the device is also configured with firewall policers. This first genuine packet received and inspected by sampled flow (sFlow) through a specific firewall policer will cause the device to reboot. After the reboot has completed, if the device receives and sFlow inspects another genuine packet seen through a specific firewall policer, the device will generate a core file and reboot. Continued inspection of these genuine packets will create an extended Denial of Service (DoS) condition. Depending on the method for service restoration, e.g. hard boot or soft reboot, a core file may or may not be generated the next time the packet is received and inspected by sFlow. This issue affects: Juniper Networks Junos OS 17.4 versions prior to 17.4R2-S9, 17.4R3 on PTX1000 and PTX10000 Series, QFX10000 Series; 18.1 versions prior to 18.1R3-S9 on PTX1000 and PTX10000 Series, QFX10000 Series; 18.2X75 versions prior to 18.2X75-D12, 18.2X75-D30 on PTX1000 and PTX10000 Series, QFX10000 Series; 18.2 versions prior to 18.2R3 on PTX1000 and PTX10000 Series, QFX10000 Series; 18.3 versions prior to 18.3R3 on PTX1000 and PTX10000 Series, QFX10000 Series. This issue is not applicable to Junos OS versions before 17.4R1. This issue is not applicable to Junos OS Evolved or Junos OS with Advanced Forwarding Toolkit (AFT) forwarding implementations which use a different implementation of sFlow. The following example information is unrelated to this issue and is provided solely to assist you with determining if you have AFT or not. Example: A Junos OS device which supports the use of EVPN signaled VPWS with Flexible Cross Connect uses the AFT implementation. Since this configuration requires support and use of the AFT implementation to support this configuration, the device is not vulnerable to this issue as the sFlow implementation is different using the AFT architecture. For further details about AFT visit the AFI / AFT are in the links below. If you are uncertain if you use the AFI/AFT implementation or not, there are configuration examples in the links below which you may use to determine if you are vulnerable to this issue or not. If the commands work, you are. If not, you are not. You may also use the Feature Explorer to determine if AFI/AFT is supported or not. If you are still uncertain, please contact your support resources.

Show More

The factory configuration for vMX installations, as shipped, includes default credentials for the root account. Without proper modification of these default credentials by the administrator, an attacker could exploit these credentials and access the vMX instance without authorization. This issue affects Juniper Networks Junos OS: 17.1 versions prior to 17.1R2-S11, 17.1R3-S2 on vMX; 17.2 versions prior to 17.2R3-S3 on vMX; 17.3 versions prior to 17.3R2-S5, 17.3R3-S7 on vMX; 17.4 versions prior to ... The factory configuration for vMX installations, as shipped, includes default credentials for the root account. Without proper modification of these default credentials by the administrator, an attacker could exploit these credentials and access the vMX instance without authorization. This issue affects Juniper Networks Junos OS: 17.1 versions prior to 17.1R2-S11, 17.1R3-S2 on vMX; 17.2 versions prior to 17.2R3-S3 on vMX; 17.3 versions prior to 17.3R2-S5, 17.3R3-S7 on vMX; 17.4 versions prior to 17.4R2-S9, 17.4R3 on vMX; 18.1 versions prior to 18.1R3-S9 on vMX; 18.2 versions prior to 18.2R2-S7, 18.2R3-S3 on vMX; 18.2X75 versions prior to 18.2X75-D420, 18.2X75-D60 on vMX; 18.3 versions prior to 18.3R1-S7, 18.3R2-S3, 18.3R3-S1 on vMX; 18.4 versions prior to 18.4R1-S5, 18.4R2-S3, 18.4R3 on vMX; 19.1 versions prior to 19.1R1-S4, 19.1R2, 19.1R3 on vMX; 19.2 versions prior to 19.2R1-S3, 19.2R2 on vMX; 19.3 versions prior to 19.3R1-S1, 19.3R2 on vMX.

Show More

A Use of Hard-coded Credentials vulnerability exists in the NFX250 Series for the vSRX Virtual Network Function (VNF) instance, which allows an attacker to take control of the vSRX VNF instance if they have the ability to access an administrative service (e.g. SSH) on the VNF, either locally, or through the network. This issue only affects the NFX250 Series vSRX VNF. No other products or platforms are affected. This issue is only applicable to environments where the vSRX VNF root password has no ... A Use of Hard-coded Credentials vulnerability exists in the NFX250 Series for the vSRX Virtual Network Function (VNF) instance, which allows an attacker to take control of the vSRX VNF instance if they have the ability to access an administrative service (e.g. SSH) on the VNF, either locally, or through the network. This issue only affects the NFX250 Series vSRX VNF. No other products or platforms are affected. This issue is only applicable to environments where the vSRX VNF root password has not been configured. This issue affects the Juniper Networks NFX250 Network Services Platform vSRX VNF instance on versions prior to 19.2R1.

Show More

A vulnerability in the BGP FlowSpec implementation may cause a Juniper Networks Junos OS device to terminate an established BGP session upon receiving a specific BGP FlowSpec advertisement. The BGP NOTIFICATION message that terminates an established BGP session is sent toward the peer device that originally sent the specific BGP FlowSpec advertisement. This specific BGP FlowSpec advertisement received from a BGP peer might get propagated from a Junos OS device running the fixed release to anothe ... A vulnerability in the BGP FlowSpec implementation may cause a Juniper Networks Junos OS device to terminate an established BGP session upon receiving a specific BGP FlowSpec advertisement. The BGP NOTIFICATION message that terminates an established BGP session is sent toward the peer device that originally sent the specific BGP FlowSpec advertisement. This specific BGP FlowSpec advertisement received from a BGP peer might get propagated from a Junos OS device running the fixed release to another device that is vulnerable causing BGP session termination downstream. This issue affects IPv4 and IPv6 BGP FlowSpec deployment. This issue affects Juniper Networks Junos OS: 12.3; 12.3X48 on SRX Series; 14.1X53 on EX and QFX Series; 15.1 versions prior to 15.1R7-S5; 15.1F versions prior to 15.1F6-S13; 15.1X49 versions prior to 15.1X49-D180 on SRX Series; 15.1X53 versions prior to 15.1X53-D238 on QFX5200/QFX5110; 15.1X53 versions prior to 15.1X53-D497 on NFX Series; 15.1X53 versions prior to 15.1X53-D592 on EX2300/EX3400; 16.1 versions prior to 16.1R7-S7; 17.1 versions prior to 17.1R2-S12, 17.1R3; 17.2 versions prior to 17.2R2-S7, 17.2R3; 17.2X75 versions prior to 17.2X75-D102, 17.2X75-D110, 17.2X75-D44; 17.3 versions prior to 17.3R2-S5, 17.3R3-S5; 17.4 versions prior to 17.4R1-S8, 17.4R2; 18.1 versions prior to 18.1R2-S4, 18.1R3; 18.2X75 versions prior to 18.2X75-D20.

Show More

When a device using Juniper Network's Dynamic Host Configuration Protocol Daemon (JDHCPD) process on Junos OS or Junos OS Evolved which is configured in relay mode it vulnerable to an attacker sending crafted IPv6 packets who may then arbitrarily execute commands as root on the target device. This issue affects IPv6 JDHCPD services. This issue affects: Juniper Networks Junos OS: 15.1 versions prior to 15.1R7-S6; 15.1X49 versions prior to 15.1X49-D200; 15.1X53 versions prior to 15.1X53-D592; 16.1 ... When a device using Juniper Network's Dynamic Host Configuration Protocol Daemon (JDHCPD) process on Junos OS or Junos OS Evolved which is configured in relay mode it vulnerable to an attacker sending crafted IPv6 packets who may then arbitrarily execute commands as root on the target device. This issue affects IPv6 JDHCPD services. This issue affects: Juniper Networks Junos OS: 15.1 versions prior to 15.1R7-S6; 15.1X49 versions prior to 15.1X49-D200; 15.1X53 versions prior to 15.1X53-D592; 16.1 versions prior to 16.1R7-S6; 16.2 versions prior to 16.2R2-S11; 17.1 versions prior to 17.1R2-S11, 17.1R3-S1; 17.2 versions prior to 17.2R2-S8, 17.2R3-S3; 17.3 versions prior to 17.3R3-S6; 17.4 versions prior to 17.4R2-S7, 17.4R3; 18.1 versions prior to 18.1R3-S8; 18.2 versions prior to 18.2R3-S2; 18.2X75 versions prior to 18.2X75-D60; 18.3 versions prior to 18.3R1-S6, 18.3R2-S2, 18.3R3; 18.4 versions prior to 18.4R1-S5, 18.4R2-S3, 18.4R3; 19.1 versions prior to 19.1R1-S3, 19.1R2; 19.2 versions prior to 19.2R1-S3, 19.2R2*. and All versions prior to 19.3R1 on Junos OS Evolved. This issue do not affect versions of Junos OS prior to 15.1, or JDHCPD operating as a local server in non-relay mode.

Show More

Receipt of a specific MPLS or IPv6 packet on the core facing interface of an MX Series device configured for Broadband Edge (BBE) service may trigger a kernel crash (vmcore), causing the device to reboot. The issue is specific to the processing of packets destined to BBE clients connected to MX Series subscriber management platforms. This issue affects MX Series running Juniper Networks Junos OS: 17.2 versions starting from17.2R2-S6, 17.2R3 and later releases, prior to 17.2R3-S3; 17.3 versions s ... Receipt of a specific MPLS or IPv6 packet on the core facing interface of an MX Series device configured for Broadband Edge (BBE) service may trigger a kernel crash (vmcore), causing the device to reboot. The issue is specific to the processing of packets destined to BBE clients connected to MX Series subscriber management platforms. This issue affects MX Series running Juniper Networks Junos OS: 17.2 versions starting from17.2R2-S6, 17.2R3 and later releases, prior to 17.2R3-S3; 17.3 versions starting from 17.3R2-S4, 17.3R3-S2 and later releases, prior to 17.3R2-S5, 17.3R3-S5; 17.4 versions starting from 17.4R2 and later releases, prior to 17.4R2-S7,17.4R3; 18.1 versions starting from 18.1R2-S3, 18.1R3 and later releases, prior to 18.1R3-S6; 18.2 versions starting from18.2R1-S1, 18.2R2 and later releases, prior to 18.2R3-S2; 18.2X75 versions prior to 18.2X75-D51, 18.2X75-D60; 18.3 versions prior to 18.3R3; 18.4 versions prior to 18.4R2; 19.1 versions prior to 19.1R1-S3, 19.1R2; 19.2 versions prior to 19.2R1-S2, 19.2R2. This issue does not affect Juniper Networks Junos OS versions prior to 17.2R2-S6.

Show More

Insufficient Cross-Site Scripting (XSS) protection in J-Web may potentially allow a remote attacker to inject web script or HTML, hijack the target user's J-Web session and perform administrative actions on the Junos device as the targeted user. This issue affects Juniper Networks Junos OS 12.3 versions prior to 12.3R12-S15; 12.3X48 versions prior to 12.3X48-D86, 12.3X48-D90 on SRX Series; 14.1X53 versions prior to 14.1X53-D51 on EX and QFX Series; 15.1F6 versions prior to 15.1F6-S13; 15.1 versi ... Insufficient Cross-Site Scripting (XSS) protection in J-Web may potentially allow a remote attacker to inject web script or HTML, hijack the target user's J-Web session and perform administrative actions on the Junos device as the targeted user. This issue affects Juniper Networks Junos OS 12.3 versions prior to 12.3R12-S15; 12.3X48 versions prior to 12.3X48-D86, 12.3X48-D90 on SRX Series; 14.1X53 versions prior to 14.1X53-D51 on EX and QFX Series; 15.1F6 versions prior to 15.1F6-S13; 15.1 versions prior to 15.1R7-S5; 15.1X49 versions prior to 15.1X49-D181, 15.1X49-D190 on SRX Series; 15.1X53 versions prior to 15.1X53-D238 on QFX5200/QFX5110 Series; 15.1X53 versions prior to 15.1X53-D592 on EX2300/EX3400 Series; 16.1 versions prior to 16.1R4-S13, 16.1R7-S5; 16.2 versions prior to 16.2R2-S10; 17.1 versions prior to 17.1R2-S11, 17.1R3-S1; 17.2 versions prior to 17.2R1-S9, 17.2R3-S2; 17.3 versions prior to 17.3R2-S5, 17.3R3-S5; 17.4 versions prior to 17.4R2-S6, 17.4R3; 18.1 versions prior to 18.1R3-S7; 18.2 versions prior to 18.2R2-S5, 18.2R3; 18.3 versions prior to 18.3R1-S6, 18.3R2-S1, 18.3R3; 18.4 versions prior to 18.4R1-S5, 18.4R2; 19.1 versions prior to 19.1R1-S2, 19.1R2.

Show More

A path traversal vulnerability in the Juniper Networks Junos OS device may allow an authenticated J-web user to read files with 'world' readable permission and delete files with 'world' writeable permission. This issue does not affect system files that can be accessed only by root user. This issue affects Juniper Networks Junos OS: 12.3 versions prior to 12.3R12-S13; 12.3X48 versions prior to 12.3X48-D85 on SRX Series; 14.1X53 versions prior to 14.1X53-D51; 15.1F6 versions prior to 15.1F6-S13; 1 ... A path traversal vulnerability in the Juniper Networks Junos OS device may allow an authenticated J-web user to read files with 'world' readable permission and delete files with 'world' writeable permission. This issue does not affect system files that can be accessed only by root user. This issue affects Juniper Networks Junos OS: 12.3 versions prior to 12.3R12-S13; 12.3X48 versions prior to 12.3X48-D85 on SRX Series; 14.1X53 versions prior to 14.1X53-D51; 15.1F6 versions prior to 15.1F6-S13; 15.1 versions prior to 15.1R7-S5; 15.1X49 versions prior to 15.1X49-D180 on SRX Series; 15.1X53 versions prior to 15.1X53-D238 on QFX5200/QFX5110 Series; 16.1 versions prior to 16.1R4-S13, 16.1R7-S5; 16.2 versions prior to 16.2R2-S10; 17.1 versions prior to 17.1R3-S1; 17.2 versions prior to 17.2R1-S9, 17.2R3-S2; 17.3 versions prior to 17.3R2-S5, 17.3R3-S5; 17.4 versions prior to 17.4R2-S9, 17.4R3; 18.1 versions prior to 18.1R3-S8; 18.2 versions prior to 18.2R3; 18.3 versions prior to 18.3R2-S3, 18.3R3; 18.4 versions prior to 18.4R2; 19.1 versions prior to 19.1R1-S4, 19.1R2.

Show More

When a device using Juniper Network's Dynamic Host Configuration Protocol Daemon (JDHCPD) process on Junos OS or Junos OS Evolved which is configured in relay mode it vulnerable to an attacker sending crafted IPv4 packets who may then arbitrarily execute commands as root on the target device. This issue affects IPv4 JDHCPD services. This issue affects: Juniper Networks Junos OS: 15.1 versions prior to 15.1R7-S6; 15.1X49 versions prior to 15.1X49-D200; 15.1X53 versions prior to 15.1X53-D592; 16.1 ... When a device using Juniper Network's Dynamic Host Configuration Protocol Daemon (JDHCPD) process on Junos OS or Junos OS Evolved which is configured in relay mode it vulnerable to an attacker sending crafted IPv4 packets who may then arbitrarily execute commands as root on the target device. This issue affects IPv4 JDHCPD services. This issue affects: Juniper Networks Junos OS: 15.1 versions prior to 15.1R7-S6; 15.1X49 versions prior to 15.1X49-D200; 15.1X53 versions prior to 15.1X53-D592; 16.1 versions prior to 16.1R7-S6; 16.2 versions prior to 16.2R2-S11; 17.1 versions prior to 17.1R2-S11, 17.1R3-S1; 17.2 versions prior to 17.2R2-S8, 17.2R3-S3; 17.3 versions prior to 17.3R3-S6; 17.4 versions prior to 17.4R2-S7, 17.4R3; 18.1 versions prior to 18.1R3-S8; 18.2 versions prior to 18.2R3-S2; 18.2X75 versions prior to 18.2X75-D60; 18.3 versions prior to 18.3R1-S6, 18.3R2-S2, 18.3R3; 18.4 versions prior to 18.4R1-S5, 18.4R2-S3, 18.4R3; 19.1 versions prior to 19.1R1-S3, 19.1R2; 19.2 versions prior to 19.2R1-S3, 19.2R2*. and All versions prior to 19.3R1 on Junos OS Evolved. This issue do not affect versions of Junos OS prior to 15.1, or JDHCPD operating as a local server in non-relay mode.

Show More

On EX4300, EX4600, QFX3500, and QFX5100 Series, a vulnerability in the IP firewall filter component may cause the firewall filter evaluation of certain packets to fail. This issue only affects firewall filter evaluation of certain packets destined to the device Routing Engine (RE). This issue does not affect the Layer 2 firewall filter evaluation nor does it affect the Layer 3 firewall filter evaluation destined to connected hosts. This issue may occur when evaluating both IPv4 or IPv6 packets. ... On EX4300, EX4600, QFX3500, and QFX5100 Series, a vulnerability in the IP firewall filter component may cause the firewall filter evaluation of certain packets to fail. This issue only affects firewall filter evaluation of certain packets destined to the device Routing Engine (RE). This issue does not affect the Layer 2 firewall filter evaluation nor does it affect the Layer 3 firewall filter evaluation destined to connected hosts. This issue may occur when evaluating both IPv4 or IPv6 packets. This issue affects Juniper Networks Junos OS: 14.1X53 versions prior to 14.1X53-D12 on QFX5100 Series and EX4600 Series; 14.1X53 versions prior to 14.1X53-D52 on QFX3500 Series; 14.1X53 versions prior to 14.1X53-D48 on EX4300 Series; 15.1 versions prior to 15.1R7-S3 on EX4300 Series; 16.1 versions prior to 16.1R7 on EX4300 Series; 17.1 versions prior to 17.1R3 on EX4300 Series; 17.2 versions prior to 17.2R3 on EX4300 Series; 17.3 versions prior to 17.3R2-S5, 17.3R3 on EX4300 Series; 17.4 versions prior to 17.4R2 on EX4300 Series; 18.1 versions prior to 18.1R3 on EX4300 Series; 18.2 versions prior to 18.2R2 on EX4300 Series.

Show More